LONCIN LC 2000i Скачать руководство пользователя страница 40

Страница: 40 / 63

SECTION 4. DISASSEMBLY AND SERVICE

c. DISASSEMBLY/ REASSEMBLY (STARTER ASSY)

The recoil starter can cause personal injury, Wear safety glasses. Do not let the recoil spring

snap out.

HEXAGON
SHOULDER BOLT

REASSEMBLY:

Apply thread locking
compound to thread
first.

REEL COVER

REASSEMBLY:

When installing, let each
ratchet’s end extend out
of the reel cover’s
corresponding gap.

Friction
spring

REASSEMBLY:

Apply grease to it.

RATCHET

REASSEMBLY:

Check for wear and
damage, pay attention
to installing direction.

REASSEMBLY:

Install return spring into
starter reel then install
starter reel onto starter
case.

STARTER REEL

RETURN SPRING

RATCHET
SPRING

Note: Take care not to let spring
snap out during disassembly. Use
gloves when disassembling.

REASSEMBLY:

Hook the outer hook in the
groove of the starter reel and
then hook inner hook

to the tab

on the starter case.

STARTER ROE

REASSEMBLY:

Check rope for
breakage and wear
before installation.

STARTER

CASE

STARTER

GRIP

- 35 -

Содержание LC 2000i
































































Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды

LONCIN LC 2000i, Руководство по обслуживанию

Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды