LONCIN LC 2000i Скачать руководство пользователя страница 11

Страница: 11 / 63

SECTION 3. MAINTENANCE

3-2 Engine Oil

NOTE: Drain the oil while the engine is still
warm to assure rapid and complete draining.

1) Place the generator on a level surface.

2) Remove the screws

①

, and then

remove the cover

②

Remove the oil filler cap

③

, drain oil from

crankcase.

4) With the engine stopped and laid on a

horizontal place, add new engine oil until oil
level reaches the oil dipstick’s upper limit, then
tighten the oil filler cap

Install the cover and tighten the screws.

Note:

Before each time of use, the generator must

be placed on a horizontal surface and check the oil
level after stopping the engine.

1.Remove the oil dipstick and wipe it clean

2. Insert dipstick into oil filler hole but don’t tighten it,

check oil level.

3. If oil level is too low, add the recommended

engine oil until oil level reaches the upper limited
shown by the dipstick.

Used motor oil may cause skin

cancer if repeatedly left in contact with the skin

for prolonged periods. Thoroughly wash your

hands with soap and water as soon as possible

after handling used oil though the cancer is not

certain to occur.

Recommended engine oil:

SAE 10W -30

Recommended engine oil grade:

API Service SE type or higher

Engine oil quantity:

0.35 L (0.42 US qt, 0.35 lmp qt)

- 6 -

Содержание LC 2000i
































































Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды

LONCIN LC 2000i, Руководство по обслуживанию

Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды