LONCIN LC 2000i Скачать руководство пользователя страница 24

Страница: 24 / 63

SECTION 4. DISASSEMBLY AND SERVICE

4-4 Engine

4-4-1 Camshaft / piston

a.DISASSEMBLY/ REASSEMBLY

REASSEMBLY:

nstall the lifters

immediately before

installing the

camshaft.

REASSEMBLY:

Install with the oil dipper toward the

governor arm’s hole end and the ribs
on the cap and connecting rod must
be aligned.

REASSEMBLY:
Push in until the bearing
touches the crankcase. Be
careful not to damage the
oil seal.

CRANKSHAFT

CONNECTING ROD CAP

OIL LEVEL

SWITCH

DECOMPRESSOR

WEIGHT

REASSEMBLY:
Check that the decompressor

weight moves smoothly, and

the spring is not weak or worn.

Install with the

timing marks

aligned.

CAMSHAFT

VALVE
LIFTER

REASSEMBLY:
Install with the
triangle mark
toward the push
rod hole.

PISTON

BREATHER
CHAMBER CAP

BREATHER
CHAMBER
PACKING

6204 BEARING

CRANKCASE
COVER PACKING

OIL SEAL 20×35×5

REASSEMBLY:

Be careful not to damage the lip of
oil seal when inserting the

crankshaft.

BOLT M6

×22

(7)

Torque: (8~12) N•m

- 19 -

Содержание LC 2000i
































































Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды

LONCIN LC 2000i, Руководство по обслуживанию

Результаты поиска

Содержание LC 2000i

Отзывы:

Похожие инструкции для LC 2000i

Бренды по названию

Популярные бренды