Lojer Scandia OT340 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 34

background image

TAMPEREEN AMMATTIKORKEAKOULU

TUTKINTOTYÖ 5(34)

Mikko Huurre

11.5.3 Tilt and lateral sensor..............................................................................................30

Replacing the sensor..........................................................................................................30

11.5.4 Height level sensor .................................................................................................30

Replacing the height level sensor ......................................................................................31

12 COLUMN.................................................................................................................................31

12.1 Adjusting the play in the column.......................................................................................31

13 MAINTENANCE SOFTWARE ..............................................................................................32

13.1 Calibrating the table sections to the zero position.............................................................32
13.2 Changing foot pedal setups ...............................................................................................33

14 SPARE PART LIST .................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

14.1 Upper frame.......................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

14.2 Base frame .........................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

14.3 Control panel .....................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

15 SCHEMATICS.........................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

15.1 Table control......................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

15.2 Remote control ..................................................

Virhe. Kirjanmerkkiä ei ole määritetty.

«
...
3
4
5
6
7
...
»

Содержание Scandia OT340



































Отзывы:

Нет отзывов

Похожие инструкции для Scandia OT340

Бренд: Raven Страницы: 48

Бренд: Pacific Страницы: 16

Бренд: Tanaka Страницы: 20

Бренд: Tandem Страницы: 80

Бренд: Tanco Страницы: 4

Бренд: UNIS Страницы: 16

Bathomatic Basic

Бренд: Unique Automation Страницы: 10

Бренд: Additel Страницы: 139

Contrology Cadillac

Бренд: Balanced Body Страницы: 7

Бренд: MÄDLER Страницы: 4

Бренд: Megger Страницы: 12

Бренд: Tecsis Страницы: 52

Бренд: Erbe Страницы: 124

SAS-1 Immunofix

Бренд: helena BioSciences Страницы: 48

Бренд: Jumper Страницы: 12

Бренд: SMC Networks Страницы: 2

Бренд: Laserworld Страницы: 34

A3x-01 Ascent Trainer

Бренд: Matrix Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды