Lojer Scandia OT340 Скачать руководство пользователя страница 30

Страница: 30 / 34

TAMPEREEN AMMATTIKORKEAKOULU

TUTKINTOTYÖ 30(34)

Mikko Huurre

11.5.2 Back section accelerometer

Back section accelerometer is located to the hinge of back part.

Accelerometer is possible to replace as the leg section accelerometer. See

11.5.1

11.5.3 Tilt and lateral sensor

Tilt and lateral sensor is located under the upper body

Replacing the sensor

Drive the table up to the maximum position and on the floor locks

(Lock)

Turn the Stand by switch to the Off position

Remove the column casing (See 8.2.2)

Disconnect the wiring, connector is located next to hydraulic

rotation valve

Undo the screws from the top of rubber cover which is fastened to

the upper cover

Release the sensor

Assemble the accelerometer in reverse order

Be sure that the wiring is same way as before

Check the wiring by moving the tilt and trendelenburg to their

extreme positions. The wiring can not be tight in any positions

11.5.4 Height level sensor

The height level sensor is located in the base of the table. The sensor is

working by using a string to measure the highness. The string is moving

with the table column and it is fastened next to hydraulic pump.

Содержание Scandia OT340



































Результаты поиска

Содержание Scandia OT340

Отзывы:

Похожие инструкции для Scandia OT340

Бренды по названию

Популярные бренды

Lojer Scandia OT340, Руководство по обслуживанию

Результаты поиска

Содержание Scandia OT340

Отзывы:

Похожие инструкции для Scandia OT340

Бренды по названию

Популярные бренды