Logik LT-48C780 Скачать руководство пользователя

Страница: 7 / 60

2 Preparation

Unpacking the TV

Remove all packaging from the TV. Retain the packaging. If you dispose of it please do so according to local regulations.

The following items are included:

Thank you

for purchasing your new JVC TV.

Your new TV has many features and incorporates the latest technology to enhance your viewing
experience. We recommend that you spend some time reading this instruction manual so that you fully
understand these features. You will also find some hints and tips to help you resolve any issues.

Read all the safety instructions carefully before use and keep this instruction manual for future reference.

Chapter

Remote Control /

AAA Batteries x 2

Instruction Manual

Quick Start Guide

Instruction Manual

48" LED Smart HD TV

LT-48C780

Please inspect your TV for damage after unpacking. If you do notice any damage please consult your dealer.

Remove all packaging from the unit. Retain the packaging. If you dispose of it please do so according to any local regulations.

  TV
  TV Stand Neck
  TV Stand Base

Remote Control/

AAA Batteries x2

Stand Neck Screws x 4
Stand Base Screws x 4

  FAV Cable
  Instruction Manual
  Quick Start Guide

Unpacking

1. Slide open the battery compartment on the back of the remote control.

Operating Your Remote Control

Thank you

for purchasing your new JVC TV.

Your new TV incorporates the latest technology to enhance your viewing

experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful first time installation.

The latest eco-friendly power-saving technology will switch off the TV if

it is left on and idle for 4 hours. Please refer to “Auto Standby” under the

“Time Settings” section of the instruction manual for more detail.

Quick Start Guide

48" LED Smart HD TV

LT-48C780

2. Insert two AAA size batteries. Make sure to match the (+) and ( - )

ends of the batteries with the (+) and ( - ) ends indicated in the battery

compartment.

3. Slide the battery compartment cover back into place. Make sure it clicks

into place.

•  Do not connect the TV to the mains supply until you have completed all the connections.
•  Always disconnect the TV from the mains socket when not in use for a long period of time.
•  The   button on the remote control is only used for switching the TV into standby, it does not disconnect the TV from the mains power.

To completely disconnect the mains power, please remove the mains plug from the mains socket.

The LCD display is very fragile, and must be protected at all times when installing and removing the base stand. Be sure that no hard or sharp object,

or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because

the screen could crack.

1. Connect one end of the RF coaxial cable to the aerial socket on the wall

and the other end of the cable to the ANT socket on the back of your TV.

2. Plug the TV into a mains socket and switch on at the mains.
3. In standby mode, press the button on the remote control to turn the

TV on. The LED indicator will flash for a few seconds then the TV will

switch on.

Connecting the Aerial and Turning on the TV

Fitting the Stand to the TV

3. Ensure the TV is switched off and not connected to the mains power supply.
4. Lay the TV down on a flat surface ideally on the edge of a table so the base of the

TV slightly overhangs the edge of the table, with the back side facing up. Please

make sure a soft cushioned material (such as a dry bath towel or thick piece of

foam) is placed beneath the screen.

5. Slide the stand under the lip, the neck will fit snugly over the screw holes. Then

screw the stand to the TV using the 4 stand neck screws supplied.

Fitting the Stand Neck and Base Together

1. Fit the neck onto the base.
2. Using the 4 stand base screws, screw the neck to the base.

Installing the Base Stand

Slide under

the lip

SCART

SPDIF