8
9
1. Antenna
2. Radiation shield &
hygro-thermo sensor
3. Mounting base
4. Battery door
5. RESET button
6. Transmission status LED
7. Bubble level
8. Rain collector
INSTALLATION INSTRUCTIONS
SETTING UP THE WIRELESS 7-IN-1 OUTDOOR SENSOR
The wireless 7-in-1 outdoor sensor measures wind speed, wind direction, rainfall, UV, light intensity,
temperature, and humidity.
9. Wind vane
10. UV/light sensor
11. Solar Cell
12. Wind cups
WIRELESS SENSOR OVERVIEW
INSTALLING THE RAIN FUNNEL
1. Align the lock grooves on the rain funnel with the lock grooves in the rain collector.
2. Lower the rain funnel onto the rain collector. Then, turn the rain funnel clockwise to lock it in place.
6
3.
GETTING STARTED
3.1
WIRELESS 7-IN-1 SENSOR
1. Antenna
7. Bubble level gradienter
2. Radiation shield & Thermo-hygro sensor
8. Rain collector
3. Mounting parts (fit for 35 ~40mm diameter pole)
9. Wind vane
4. Battery door
10. UV / light sensor
5.
[ RESET ]
key
11. Solar panel
6. Transmission status LED
12. Wind cups
6
3.
GETTING STARTED
3.1
WIRELESS 7-IN-1 SENSOR
1. Antenna
7. Bubble level gradienter
2. Radiation shield & Thermo-hygro sensor
8. Rain collector
3. Mounting parts (fit for 35 ~40mm diameter pole)
9. Wind vane
4. Battery door
10. UV / light sensor
5.
[ RESET ]
key
11. Solar panel
6. Transmission status LED
12. Wind cups
6
3.
GETTING STARTED
3.1
WIRELESS 7-IN-1 SENSOR
1. Antenna
7. Bubble level gradienter
2. Radiation shield & Thermo-hygro sensor
8. Rain collector
3. Mounting parts (fit for 35 ~40mm diameter pole)
9. Wind vane
4. Battery door
10. UV / light sensor
5.
[ RESET ]
key
11. Solar panel
6. Transmission status LED
12. Wind cups
INSTALLING THE BATTERIES
1. Loosen the screw at the joint of the solar cell so the gear on the other side of the joint pushes out. The
solar cell should now be in an unlocked position.
2. Move the solar cell out of the way of the battery door.
3. Unscrew the battery door at the bottom of the 7-in-1 outdoor sensor using a screwdriver (not included).
7
3.1.1 INSTALL RAIN GAUGE FUNNEL
Install the rain gauge funnel and rotate clockwise to lock the funnel to the sensor array
Rain Collector Installation
1 Align
Lock grooves
2 Lock
3.1.2 INSTALL RECHARGEABLE BATTERIES
Step 1: Unscrew the battery door at bottom of unit and take
out the cable socket.
Step 2: Connect the Ni-MH rechargeable battery plug to the
socket.
Step 3: Make sure the red LED indicator on the back of the
sensor array is turn on and then begin flashing every 12
seconds.
Step 4: Adjust the cable and socket into shallow hole and put
the battery pack into the battery compartment.
1
7
9
10
11
12
8
3
4
2
5
6
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
The red LED will begin flashing every 12 seconds.
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meter
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
1
2