LOFTNESS 77-001 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

LOFTNESS 77-001 Скачать руководство пользователя страница 13

5

Fertilizer Tender OM

Maintenance Safety

• Follow the maintenance schedule outlined in this

manual.

• Do no operate a unit that is defective or has missing

or worn parts.

• Do not allow inexperienced persons unfamiliar with

the machine, or unfamiliar with safe operating and
maintenance procedures, to operate or maintain the
machine.

• Do not allow persons under the influence of alcohol,

medications, or other drugs that can impair judgment
or cause drowsiness to operate or maintain the
machine.

• Make sure the operator’s area is clear of any

distracting objects. Keep work areas clean and free
of grease and oil to avoid slipping or falling.

• Periodically check all guards, shields and structural

members. Replace or repair anything that could
cause a potential hazard.

• Periodically check all hoses, hose connections,

hydraulic system, and electrical wiring. Replace or
repair anything that could cause a potential hazard.

• Do not replace components or parts with other than

factory-recommended service parts. To do so may
decrease the effectiveness of the machine.

• Do not lubricate parts while the machine is running.

• Do not smoke while servicing the machine.

• Never attempt to make any adjustments while the

truck’s engine is running or the key is in the “ON”
position in the truck. Before leaving the operator’s
position, turn engine off and remove ignition key.

• Remove hydraulic pressure by operating control

levers to all positions - with engine turned off, before
performing any service on the tender.

• Set parking brake in truck cab and chock wheels

before perming any maintenance or repairs on the
machine.

• Place stands or blocks under the frame before

working beneath.

Safety Instructions

Hydraulic Safety

• The hydraulic system is under high pressure. Make

sure all lines and fittings are tight and in good
condition. These fluids escaping under high pressure
can have sufficient force to penetrate skin and cause
serious injury.

• Never check for leaks by using any part of your body

to feel for escaping fluid.

• Always use a piece of wood to check for leaks.

• Immediately replace any worn or damaged hydraulic

hoses.

• Lower auger and shut engine off to relieve system

pressure before loosening any hydraulic line or
connection.

• Loosen connections slowly, keeping hands and

fingers clear of loosened fittings.

• Make sure hydraulic connections are tightened

before applying pressure.

• Do not make any make-shift repairs to hydraulic

hoses, fittings, or any components using clamps,
sealers, tape, etc. as these attempts will fail, creating
a hazardous situation.

•

If injured by escaping hydraulic fluid, seek immediate
medical attention as serious side affects and death
can occur.

«
...
11
12
13
14
15
...
»

Содержание 77-001





















































Отзывы:

Нет отзывов