- 8
Deutsch
English
Français
Italiano
Español
Nederlands
Start-up and settings
Before commencing the start-up and settings, please make sure that all cables
are connected correctly.
Switching the subwoofer on/off
Use the mains switch
Power
5
to switch the subwoofer on in position
ON
and
off in position
OFF
.
➠
If you wish to toggle between the operating modes Wireless or Cable via
Audiolink
, switch the unit off for minimum 30 seconds and then on again.
Mode with Loewe TV sets
If the subwoofer is connected via the
Audiolink
connection, as described on
2
the
Mode - ON/AUTO
7
switch is in the
AUTO
position and
the
Mode - 2.1/Stereo
6
switch is on the
2.1 position
, you no longer need to
switch the subwoofer on and off separately. After switching on the subwoofer for
the first time, it is automatically switched on and off together with the Loewe TV set.
➠
Register the presence of the subwoofer as described in the instructions for
use of your Loewe TV set under "Operating extra devices" or "External
devices".
Automatic operation with other audio sources
If there is no
Audiolink
connection, the
Mode - ON/AUTO
7
switch is at the
AUTO
position and if audio signals are present at the Cinch sockets
Line IN - Right/
Subw/Left
1
the
subwoofer will switch on automatically. After 10 minutes with-
out an audio signal at these sockets, the subwoofer will switch off automatically.
➠
The subwoofer can switch on automatically if fault signals are present on
the audio lines. In this case, activate the mains switch
5
.
➠
The subwoofer can switch off automatically during longer, very quiet pas-
sages. In this case, increase the volume.
Continuous operation with other audio sources
If you wish to operate the subwoofer in continuous mode, switch the
Mode - ON/
AUTO
7
switch to the
ON position
. Then switch the subwoofer on or off with
the mains switch
Power
5
.
Stereo mode
Move the
Mode - 2.1/Stereo switch
6
switch to the
Stereo
position if you are
only feeding the audio signals in at the Cinch sockets
Line IN - Right/Left.
1
The bass manager integrated in the subwoofer then automatically directs the bass
components contained in the stereo signals to the subwoofer channel.
2.1 Mode
Move the
Mode - 2.1/Stereo switch
6
switch to the
2.1
if you are feeding the
audio signals in at the Cinch sockets
Line IN - Right/Subw/Left
1
.
Wireless
Move the
Mode - ON/AUTO
7
switch to the
ON
position if you wish to connect
the subwoofer to a compatible audio source via a wireless link. Activate Coupling
mode, as described in the instruction manual of the relevant audio source. Use
a sharp object (e.g. paper clip) and press briefly on the button in the opening to
move
8
the
optional
Module Wireless Audiolink
in Coupling mode. If the
registration was not successful, please try again and reduce the distance of the
subwoofer to the audio source.
➠
The distance between the subwoofer and audio source must not exceed 10
m in the same room.
➠
The rotary switches
Crossover Frequency
9
,
Equalizer
10
and
Bass
Intensity
11
do not have any function in the
Wireless
operating mode.
Setting the crossover frequency
The
Crossover Frequency knob
9
gives you the option to set the limit frequency
for the bass playback - depending on which speakers you have connected - between
50 Hz and 350 Hz.
As described on page 7, for Loewe audio systems the knob should be set to 350
Hz because the crossover frequency is set to this in the Loewe audio sources (TV set).
Setting the equalizer
The
Equalizer
knob
10
gives you the option of setting a reduction or increase in
the lowest frequency ranges (20 Hz - 50 Hz) for the bass playback.
• If the subwoofer is near the corner of the room, turn the
Equalizer knob
10
more towards
-3 dB
.
• If the subwoofer is near a wall, then turn the
Equalizer
knob more to the
middle position.
• If the subwoofer is freestanding in the room, turn the
Equalizer knob
10
more towards
+3 dB
.
Bass intensity
You can use the
Bass Intensity
control
11
to set the basic bass volume to how
you want it.
