Loctite VoluDrop UV 97650 Скачать руководство пользователя страница 13

Страница: 13 / 18

6 Maintenance

The VoluDrop Dispenser requires no special care.

As maintenance only a sealing ring inside has to be replaced regularly.
The dispenser has to be cleaned, if it is dismantled for replacing the sealing rings, see
section 5.1.

The maintenance interval is at a

dispensing rate of :
–  10 shots/minute (smallest amount)
    every   7 days.
–  4 shots/minute (biggest amount)
    every 2-3 weeks.

•

Dismantle the dispenser according to

the right graphic.

The number 9 shows the supplied
assembly tool for maintenance.

•

Unscrew thread disk D with the help of a

screwdriver.

•

Remove the shim rings E and keep

them ready

•

Use the assembly tool 9 to dismantle

the gasket C and the sealing ring B.

•

Replace the sealing ring E.

•

Replace the gasket C and the sealing

ring B and mount the new one’s with the
help of the assembly tool 9.

Содержание VoluDrop UV 97650



















Результаты поиска

Содержание VoluDrop UV 97650

Отзывы:

Похожие инструкции для VoluDrop UV 97650

Бренды по названию

Популярные бренды

Loctite VoluDrop UV 97650, Руководство по эксплуатации

Результаты поиска

Содержание VoluDrop UV 97650

Отзывы:

Похожие инструкции для VoluDrop UV 97650

Бренды по названию

Популярные бренды