background image

9

3  

Operating instructions

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING:

 If you do not follow these instructions exactly, a fire or explosion 

may result causing property damage, personal injury, or loss of life. 

A.  This appliance does  not  have  a pilot.   It  is 

equipped with an  ignition device which 
automatically lights the burner.   Do  not try 
to light the burner by hand. 

B.  BEFORE OPERATING smell all  around 

the  appliance area  for gas.  Be sure to 
smell next to the floor because  some gas 
is heavier than air  and will settle  on the 
floor. 

WHAT TO DO IF YOU SMELL GAS 

 

Do not try  to light any  appliance. 

 

Do not touch  any electric switch; do 
not use any phone in your building.  

 

Immediately call your gas supplier from a 
neighbor’s phone.   Follow  the  gas supplier’s 
instructions.  

 

If you cannot reach your gas supplier, call 
the fire  department. 

C.  Use only your hand  to turn the gas  control knob.   

Never use tools.  If the handle will not turn by 
hand, don’t try to repair it, call a qualified service 
technician.  Force or attempted  repair  may  result 
in a fire or explosion. 

D.  Do not use  this appliance if  any part has  been 

under water.  Immediately call a qualified 
service  technician to inspect the appliance and 
to  replace any part  of the control system and 
any gas control which has been under water. 

OPERATING INSTRUCTIONS

1. 

STOP!

   Read the safety information 

above  on this label. 

2.  Set the thermostat to lowest  setting. 

3.  Turn off  all  electric power to the 

appliance. 

4.  This appliance is equipped with  an 

ignition device which automatically lights 
the burner.  Do not try to light the burner 
by hand. 

5. Remove 

front 

door. 

6.  Turn gas shutoff valves counterclockwise 

to “OFF”.   Handle will be  perpendicular  to 
pipe.  Do not force.  

7.  Wait five (5) minutes to clear out any gas.  

If you then smell gas, 

STOP!

  Follow “B” 

in the safety  information above this label.  
If you don’t  smell gas, go  to next step. 

8.  Turn gas shutoff valve clockwise to “ON”.  

Handle will be parallel to pipe. 

9. Install 

top 

cover. 

10. Turn on all electric power to  appliance. 

11. Set thermostat to desired setting. 

12. If the appliance will not operate, follow the 

instructions “To Turn  Off Gas To Appliance” and 
call your service technician or gas supplier. 

TO TURN OFF GAS TO APPLIANCE

1.  Set the thermostat to lowest  setting. 

2.  Turn off  all  electric power to the appliance 

if service is to be performed. 

3. Remove 

front 

door. 

4.  Turn gas shut off valves counterclockwise to 

“OFF”.  Handle will be perpendicular to pipe.   
Do not force.  

5.  Install front door. 

LBL20053 REV A 

Gas Valve

OPEN

Gas Valve

CLOSED

                  

User’s Information Manual 

Содержание SYNC 1.0

















Отзывы: