LOBSTER SPORTS Phenom 1 Скачать руководство пользователя страница 10

Страница: 10 / 12

[email protected]

Phone: 800.526.4041

Fax: 818.764.6061

Author: JJ Contributors: RR, CT Original Date:11/2/12 Revision: 2/17/2022

TS- I have an Over-Current or Feedback Sweep/ Elevation Error.

Trouble Shooting Instructions

Elevation Motor (Timing Disc highlighted in green). Visible through the rear Circuit

board side of the hopper

Check the Snap-In Sensors located at the
back portion of the Proxy Mount Assembly.
(It is below the Proxy Mount Magnet Holder.

Make Sure the sensor is plugged in all the
way- by grabbing the 3 wires (red, black and
green), and CAREFULLY pulling a little bit
away from the Elevation/ Sweep Assembly.
(

If you feel any resistance then the snap-in

sensor is in place. DO NOT TUG ON WIRES
TOO HARD!)

Elevation Motor (Snap-in Sensor highlighted by green

Содержание Phenom 1













Результаты поиска

Содержание Phenom 1

Отзывы:

Похожие инструкции для Phenom 1

Бренды по названию

Популярные бренды

LOBSTER SPORTS Phenom 1, Инструкция по эксплуатации

Результаты поиска

Содержание Phenom 1

Отзывы:

Похожие инструкции для Phenom 1

Бренды по названию

Популярные бренды