7
Faucet diverter
Faucet
Cable tie
Steel hose for
alkaline water
Acidic water hose
Power cord
connection (5 ft)
Control panel
Base Unit Installation
Place the water ionizer on the countertop in close proximity to the sink. The assembly should be relatively
near the spigot to maximize flow rate. Please leave at least 20cm clearance for filter replacement.
Optional Accessories
The quality and content of the source water provided to the water ionizer has a direct affect on the quality of the
ionized water produced. This is true of ANY water ionizer. Tap water provided by municipal water companies
typically has a pH value between 7.1 and 7.3 and a moderate water hardness of between 80 and 140 parts per million.
Such water will generally result in the production of high quality ionized water. Water supplied from other sources
may vary considerably in quality and content. Low pH water (typical of some well water) may require an additional
pre-remineralization cartridge to enhance water ionization. Water with excessive sediment (typical of well water)
generally requires a sediment prefilter. Your Dealer can help you decide if additional water conditioning is required.
INSTALLATION
Setup Illustration
Suction cup
6
I N S TA L L AT I O N
IMPORTANT NOTICE:
Failure to install according to the Installation Guide and in accordance with applicable city, state and local
plumbing codes can result in leaks and/or water damage and will void your warranty. We expressly disclaim any liability for damage
caused by leaks and/or other water damage.
NOTE:
The installation information provided may differ for your specific installation. Read the installation section thoroughly before
you begin as additional installation parts may be required beyond what are included. If you are unsure what parts are required or how
to make the physical connections, it is strongly recommended you contact a licensed plumber.
• The water ionizer MUST be plugged into a grounded (three prong) 120 Volt electrical outlet that is installed in
accordance with all local codes and ordinances. Check with a qualified electrician if you are not sure whether the
electrical outlet you intend to use is properly installed. Do not modify the electrical power cord or plug provided with
the water ionizer and do not use a three-prong to two–prong adapter. Improper grounding can result in risk of electric
shock as well as damage to the water ionizer.
• Do not plug the water ionizer into an electrical outlet that will result in exceeding the amperage rating of the outlet or
electrical wiring. This can result in fire, personal injury or damage to the water ionizer.
• The water ionizer must operate in a dry location to prevent risk of electrical shock and/or damage to the unit.
• The water ionizer must operate on a FLAT/hard/level surface.
• Maximum water pressure is 50 PSI. Operating the water ionizer above this pressure will cause damage to the unit. For
psi >50 use of a pressure regulator may be required.
• Connect the water ionizer ONLY to a
COLD
water supply.
NEVER
run hot water through the unit. Damage will occur if
HOT WATER is supplied to the water ionizer.
• DO NOT DRINK WATER PRODUCED WHEN THE WATER IONIZER IS IN ITS CLEANING CYCLE. The cleaning cycle
will automatically activate after every 40 liters of water is produced. This feature helps keep minerals from building up
on the electrolysis plates.
• Use the “Filtered Water Only” setting when taking medications. Alkaline water will increase the potency of many
medications. Check with your physician to make sure prescribed medications for existing conditions will not be
adversely affected by drinking alkaline water on a daily basis.
NOTE:
Insert water supply and drain lines into the quick connects until they will not go in any further. Use of the locking clip to prevent the
tube from coming loose is a must. Give each line a slight tug at the point of connection to make sure the lines are properly connected and
that they do not slip out. This step will ensure proper installation and avoid possible leaks from improperly installed lines.
NOTE:
To achieve optimal pH and ORP performance it may be necessary to install the re-mineralization cartridge between the source water
and C7 product. Depending on your local water TDS levels, it may be necessary to adjust the Ionizer plate power setting. Follow the
instructions for "Programing the C7".