manualshive.com logo in svg

Little Wonder Xtra, Руководство владельца оператора

Поделиться
Скачать
Little Wonder Xtra Скачать руководство пользователя страница 6

S

AFE

F

UELING

I

NSTRUCTIONS

Refuel outdoors only.  Always switch off the
engine and allow it to cool before refueling.
Relieve fuel tank pressure by loosening fuel 
cap slowly.  Never remove fuel filler cap while
engine is running.

Select bare ground for fueling, then move at
least 10 feet from the fueling spot before start-
ing the engine.  Wipe off any spilled fuel before
starting your Xtra Edger and check for leakage.

Always tighten fuel filler cap securely after 
fueling.

S

AFE

S

TARTING

You should always inspect your unit before
starting it.  Make sure the controls and safety
devices are working properly.

For specific starting instructions, see the 
appropriate section of this operators manual.  

Place the machine on firm ground or other solid
surface in an open area.  Maintain good balance
and secure footing.
Failure to follow this procedure may result in

injury to hand or fingers or may damage the
starter mechanism.

S

AFE

W

ORKING

I

NSTRUCTIONS

AND

I

MPORTANT

A

DJUSTMENTS

Never operate your machine if it is damaged,
improperly adjusted or not completely and
securely assembled.  At correct idle speed, the
blade should not turn.  Do not use the Xtra
Edger with incorrect idle speed; see the speed
setting instructions on page 13.

S

AFE

M

AINTENANCE

, R

EPAIR AND

S

TORING

Use only original Little Wonder replacement
parts for maintenance and repair.  Use of parts
manufactured by others will void warranty
and/or may cause serious or fatal injury.

Follow the maintenance instructions in the
appropriate section of this manual.  Any repairs
should be carried out by an authorized service
dealer.

WARNING

Always allow engine to cool before 

refueling.  Accidental spillage of gasoline

over hot engine could cause fire or 

explosion to occur with consequent 

possible disfigurement or fatal injury.  

Wash and clean hands after fueling.

▲

!

▲

!

WARNING

The Xtra Edger is a one-person 

machine.  To reduce the risk of eye or 

other injury from thrown objects, 

ensure that bystanders are at least 50 

feet away during use.  Replace 

immediately any worn or broken debris

deflector shield or blade cover.  If

approached, release throttle trigger to

immediately deaccelerate the engine.

▲

!

▲

!

WARNING

When you pull the starter grip, do not

wrap starter rope around your hand.

Do not allow grip to snap back, but

guide starter rope slowly back to 

permit rope to rewind properly.

▲

!

▲

!

6

WARNING

Always stop the engine, make sure that 

the blade is stopped, and disconnect 

the spark plug before adjusting blade

height, doing any maintenance or repair

work, or cleaning the unit or blade.

▲

!

▲

!

Содержание Xtra

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды