background image

Schiller-Pfeiffer, Inc. warrants each new Little
Wonder Xtra Edger for ONE YEAR for residential
use based on the following terms.

This warranty extends to the original retail purchaser
only and commences on the date of the original
retail purchase.

Any part of the Little Wonder Xtra Edger 
manufactured or supplied by Little Wonder and found
in the reasonable judgement of Little Wonder to be
defective in material or workmanship will be repaired
or replaced by an authorized Little Wonder service
dealer without charge for parts and labor.

The Little Wonder Xtra Edger, including any 
defective part, must be returned to an authorized
service dealer within the warranty period. The
expense of delivering the Little Wonder Xtra Edger to
the dealer for warranty work and the expense of
returning it back to the owner after repair or
replacement will be paid for by the owner. Little
Wonder’s responsibility in respect to claims is limited
to making the required repairs or replacements and
no claim of breach of warranty shall be cause for
cancellation or rescission of the Contract of Sale of
any Little Wonder Xtra Edger. Proof of purchase will
be required by the dealer to substantiate any 
warranty claim. All warranty work must be 
performed by an authorized Little Wonder service
dealer or by Schiller-Pfeiffer, Inc.

This warranty is limited to the one (1) year from the
retail date of original purchase. Engine warranted
separately by engine manufacture.

This warranty does not cover any Little Wonder Xtra
Edger that has been subject to misuse, neglect, 
negligence or accident, or that has been operated 
in any way contrary to the operating instructions as
specified in the Little Wonder Xtra Operator’s
Manual. This warranty does not apply to any 
damage to the Little Wonder Xtra Edger that is the
result of improper maintenance or to any Little
Wonder Xtra Edger that has been altered or 
modified so as to adversely affect the product’s 
operation, performance or durability or that has been
altered or modified so as to change its intended use.
The warranty does not extend to repairs made 
necessary by normal wear or by the use of parts 
or accessories which are either incompatible with 
the Little Wonder Xtra Edger or adversely affect 
its operation, performance or durability.

Little Wonder reserves the right to change or
improve the design of any Little Wonder Xtra Edger
without assuming any obligation to modify any prod-
uct previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN
DURATION TO THE ONE YEAR WARRANTY 
PERIOD, ANY SUCH IMPLIED WARRANTIES,
INCLUDING MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR OTHERWISE, ARE
DISCLAIMED IN THEIR ENTIRETY AFTER THE
EXPIRATION OF THE APPROPRIATE TWELVE (12)
MONTH WARRANTY PERIOD. LITTLE WON-
DER’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLY AND EXCLUSIVELY LIMITED TO THE
REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS AND LITTLE WONDER DOES NOT
ASSUME OR AUTHORIZE ANYONE TO ASSUME
FOR THEM ANY OTHER OBLIGATION. SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.

LITTLE WONDER ASSUMES NO RESPONSBILITY
FOR INCIDENTAL, CONSEQUENTIAL OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO,
EXPENSE OF RETURNING THE LITTLE WONDER
PRODUCT TO AN AUTHORIZED SERVICE DEAL-
ER AND EXPENSE OF DELIVERING IT BACK TO
THE OWNER, MECHANIC’S TRAVEL TIME, TELE-
PHONE OR TELEGRAM CHARGES, RENTAL OF A
LIKE PRODUCT, DURING THE TIME WARRANTY
SERVICE IS BEING PERFORMED, TRAVEL, LOSS
OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OR TIME, OR INCONVENIENCE. SOME
STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.

This warranty applies to all Little Wonder Xtra
Edgers manufactured by Little Wonder.

LITTLE WONDER

®

1028 Street Road, Southampton, PA  18966

Tel. (215) 357-5110    Fax (215) 357-8045

Division of Schiller-Pfeiffer Inc.

©2003 Little Wonder Div. of Schiller-Pfeiffer, Inc.   P/N 100700

Содержание Xtra

































Отзывы: