INTRODUCTION
EN
This instruction sheet provides you with the information required
to safely own and operate your Little Giant product. Retain these
instructions for future reference.
The Little Giant product you have purchased is of the highest
quality workmanship and material, and has been engineered to
give you long and reliable service. Little Giant products are care-
fully tested, inspected, and packaged to ensure safe delivery and
operation. Please examine your item(s) carefully to ensure that
no damage occurred during shipment. If damage has occurred,
please contact the place of purchase. They will assist you in
replacement or repair, if required.
READ THESE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL, OPERATE, OR SERVICE
YOUR LITTLE GIANT PRODUCT. KNOW THE PRODUCT’S
APPLICATION, LIMITATIONS, AND POTENTIAL HAZARDS.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL
SAFETY INFORMATION. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/
OR PROPERTY DAMAGE!
DESCRIPTION
The FP series Flex Pumps provide circulating, oxygenated water
to features such as ponds, fountains, displays, waterfalls, and
filter systems.
SAFETY GUIDELINES
WARNING: RISK OF ELECTRICAL SHOCK. PLEASE OBSERVE
THE FOLLOWING SAFETY GUIDELINES.
WARNING:
This pump has not been investigated for use in swim-
ming pools.
This pump uses a grounding conductor and a grounding-type
attachment plug. To reduce the risk of electrical shock, connect the
pump only to a properly grounded, grounding-type receptacle.
Employ a qualified, licensed electrician to provide electrical
power.
Check product label for proper voltage required. Do not connect
to voltage other than that shown.
To comply with the National Electric Code (NEC) and to reduce
the risk of electric shock, connect the pump only to an outlet pro-
tected by a ground fault circuit interrupter (GFCI).
Check the power cord regularly to ensure that it is in good condi-
tion, with no nicks or cuts.
Do not lift the pump by its power cord.
Do not let the pump freeze during colder temperatures. This can
cause cracking or distortion that will damage the pump. See the
MAINTENANCE section for storage instructions.
Do not operate the pump dry. This will cause the pump to become
extremely hot, causing burns if touched and/or damage to the
pump.
Do not use to pump water hotter than 95°F (35°C).
INSTALLATION AND OPERATION
WARNING:
Ensure that the installation conforms with all local and
state electric codes.
NOTE:
The pump has thermal overload protection. If it becomes
overheated it will shut off. See the Troubleshooting section to
restart.
In-Water (Submersible) Installation
Refer to Figure 1, Figure 2, and the following steps to configure
the pump for in-water (submersible) use:
1. Locate the connection box in a dry area at least 6-1/2 feet (2
meters) from the edge of the water.
2. Place the pump into the water on a flat surface, ensuring that
the pump is completely submersed and that the volute is filled
with water.
CAUTION:
If the surface is dirt or sand, place the pump on a
flat object such as a brick or stone to prevent clogging. For
best results, place the pump into a skimmer.
CAUTION:
Ensure that the water level does not go below
25cm (FP1, FP2, and FP3) or 30cm (FP6 and FP9).
3.
FP1, FP2, and FP3 ONLY:
The discharge can be configured
to point up or to the side, depending on the application. To
redirect the discharge, loosen the four clip screws (1), turn the
motor housing (9) until the discharge is in the desired position,
and tighten the screws.
4. Make all necessary intake and discharge connections.
NOTE:
Use a pre-filter on the intake for added protection from
clogging.
FP SERIES FLEX PUMP •
POMPE FLEX DE
SÉRIE FP • SERIE FP
BOMBA FLEXIBLE
1
Franklin Electric Co., Inc.
P. O. Box 12010
Oklahoma City, OK 73157-2010
888.956.0000 • Fax: 405.947.8720
www.LittleGiantWater.com
Min. 6.5 ft. (2m)
Min. 10 in. (25cm)
FIGURE 1
Min. 6.5 ft. (2m)
Min. 10 in. (25cm)
FIGURE 2
