manualshive.com logo in svg

Lithium Grim OmniWah, Инструкция по сборке

Поделиться
Скачать
Lithium Grim OmniWah Скачать руководство пользователя страница 16

OmniWah v2.0 

 

Manufacturers and product names are mentioned solely for circuit identification, and where applicable their trademarks are the 
property of their respective owners who are in no way associated or affiliated with the author. No cooperation or endorsement 

is implied.

 

16 

Wahpot calibration 

If you feel that your wah is not changing over the full sweep, then you will need to calibrate your 
wahpot. You can do this by loosening the tension clutch (the white plastic thingy pushing against the 
rack gear) until you can push it aside enabling you to pull back the rack gear from the wahpot. Do not 
totally unscrew it! 

 

 

 

 

 

 

 
Connect your wah to your guitar and amp (and power if needed). Push the rack gear against to the 
teeth of the wah pot ensuring the gears fall in to place without using force, and rock the wah to find 
out at which end (heel or toe) there is too little change in the wah sound. Once you find it, push back 
the rack gear and just slightly adjust the wah gear by turning the wah pot. It is important that you try 
to do this just 1 tooth at a time, else you will overshoot the sweet spot before you know it! Also be 
careful to not overturn the wahpot in either of the extreme directions of the rack gear. This could 
cause the gears slip and break after a while as the rocker has more motion than the gears and teeth 
will allow!  

This is how I start. Let’s say there is too little action in the toe position. I start by pushing the rocker in 
the most extreme toe position, clicking the footswitch. I pull the rack gear back, turn the wahpot in 
the most extreme toe position and turn it back 2 teeth on the wahpot. I push back the rack gear to 
the wahpot and test it again. If there is still not enough action in the toe position I repeat this and 
turn the wahpot 1 tooth further. At this point you should always check that in the heel position you 
still have enough gears left so it does not slip in the heel position. Repeat as many times as possible.  
Do not forget to refasten the tension clutch once you are done. 

If you still do not get the desired sweep then it is time to look at a different taper wahpot! 

 

 

Rack gear 

Tension clutch 

Содержание OmniWah




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды