manualshive.com logo in svg

Lithium Grim OmniWah, Инструкция по сборке

Поделиться
Скачать
Lithium Grim OmniWah Скачать руководство пользователя страница 10

OmniWah v2.0 

 

Manufacturers and product names are mentioned solely for circuit identification, and where applicable their trademarks are the 
property of their respective owners who are in no way associated or affiliated with the author. No cooperation or endorsement 

is implied.

 

10 

Note:

 Orientation of the transistors vary for each different type you use. For this reason I marked the 

pinout on the board for your convenience. I also added a graphic of the flat and rounded side of the 
transistor. This is based on the vintage transistors. Eg. a MPSA needs to be rotated 180 degrees! 
Always consult the 

datasheet

 of the transistor and orient accordingly. 

If you need to cross 2 legs of a transistor, you can use shrink wrap around the legs so they do not 
short eachother. 

Now continue by soldering the small capacitors (MLCC) then the small SMF, trimpots and then the 
Electrolytic capacitors. Finish with soldering the inductor.  

I suggest you now drill the holes in your enclosure (maybe a spare old crybaby shell) so you can use it 
during the off board wiring. Try to keep wires as short as possible. 

Note:

 Really take some time to determine where to place the pots, switches, jacks and  PCB in the 

enclosure before you start drilling (if any drilling is needed at all). Measure twice, drill once. 

You are almost ready to rock, well… not really. The difficult part starts now. Besides the components 
mentioned in the components table, you will need: 

 

1 x 3PDT footswitch

 (9 pins)  

 

9v battery clip

 (optional).

 

 

22 gage stranded hook-up wire. 

 

A LED holder. 

This enables you to mount the LED in the enclosure. 

 

Wah enclosure

 (new or used). This is actually also optional. You can build this board into a 

1590BB and make it a fully customizable fixed/cocked wah. For this there are 4 mounting 
holes added to the PCB for the standoffs. 

 

 

Содержание OmniWah




















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды