background image

3. Installation Preparation.

page 3

ON

OFF

ON

OFF

To prevent personal injury and damage, 
ensure that the hanging location allows the 
blades a clearance of 7ft. (2.13m) from the 
floor and 30in. (76cm) from any wall or 
obstruction. 
This fan is suitable for room sizes up to 400  
square feet (37.2 square meters).

This fan can be mounted with a 

downrod

on a normal or vaulted ceiling. The hanging 
length can be extended by purchasing a 
longer downrod (0.5in./1.27cm diameter). 
Other installation, such as 

flushmount

, is 

not

 

available for this fan.

Installation requires these tools: 

Phillips screwdriver, flathead screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

Vaulted ceiling 
angle is not to 
exceed 25 degrees.  

downrod

installation

flushmount

installation

12f

t.

  - 20f

t.

12ft. - 20ft.

(3.66m - 6.1m)

(3.66m - 6.1m)

7 feet

(2.13m)

(76cm)

30 

inches

4. Hanging Bracket Installation.

Turn off circuit breakers to current fixture from 
breaker panel and be sure operating light switch is 
turned to the OFF position. 

WARNING: 

Failure to disconnect power supply prior 

to installation may result in serious injury.

Remove existing fixture. 

WARNING:

 When using an existing outlet box, be 

sure the box is securely attached to the building 
structure and can support the full weight of the fan. 
Ensure it is clearly marked "Suitable for Fan Support." 
If not, it must be replaced with an approved outlet 
box. Failure to do so can result in serious injury.

Install hanging bracket to outlet box using original 
screws, spring washers and flat washers (size 8 or 
M5) provided with new or original outlet box.

If 

installing on a vaulted ceiling, face opening of 
hanging bracket towards high point of ceiling. 
Arrange electrical wiring around the back of the 
hanging bracket and away from the bracket 
opening.

*Note

: It is very important that you use the proper hardware when installing the hanging bracket as this will 

support the fan. Please make certain that you purchase any hardware that is missing in order to install the 
hanging bracket properly.

 blade edge

hanging bracket

spring washers

outlet box screws

flat washers

Содержание PZ52ABZ5C











Отзывы: