A
WIRING
(continued on next page)
4
2.
Remove pin (Q) and clip (R) from motor housing yoke. Slip downrod
(A) into motor housing yoke, align holes and re-install pin (Q) and clip
(R). Tighten downrod set screws and then tighten nuts. Slide yoke cover
(F) down until it rests on top of motor housing (E). [Fig. 2]
Fig. 1
Fig. 2
NORMAL OR ANGLE STYLE FAN MOUNTING
3.
Install ball end of downrod (A) into mounting bracket (C) opening.
Align slot in ball with tab in mounting bracket (C). [Fig. 3]
Warning:
Failure to align slot in ball with tab in mounting bracket
(C) may result in serious injury or death.
Fig. 3
Q
1.
Choose downrod (A) length you wish to use.* If you choose to use
the 12 in. downrod (A), remove hanging ball from the 6 in. downrod (A)
and attach the hanging ball to the 12 in. downrod (A). Insert downrod
(A) through canopy (B) and yoke cover (F). Thread wires from motor
housing (E) through downrod (A). [Fig. 1]
*Helpful Hint:
Downrod style mounting is best suited for ceilings 8 ft.
(2.44 m) high or higher. For taller ceilings you may want to use a longer
downrod (not included) than the ones provided. Angle style mounting is
best suited for angled or vaulted ceilings. Longer downrods are
sometimes necessary to ensure proper blade clearance.
Note:
Black wire is hot power for fan. Blue wire is hot power for
light kit. White wire is common for fan and light kit. Green or bare
wire is ground.
B
F
R
E
SWITCHED LIGHT POWER
WHITE (NEUTRAL)
BLACK (POWER)
GROUND
GROUND
WHITE
SWITCHED LIGHT POWER
WHITE (NEUTRAL)
GROUND
BLACK
BLUE
GROUND
WHITE
SWITCHED FAN POWER
FAN CONTROLLED BY CHAIN, LIGHT BY WALL SWITCH.
FAN AND LIGHT CONTROLLED BY SEPARATE WALL SWITCHES.
Fig. 1B
Fig. 1C
WARNING:
To reduce the risk of fire, electrical shock, or
personal injury, wire connectors provided with this fan are designed
to accept only one 12 gauge house wire and two lead wires from
the fan. If your house wire is larger than 12 gauge or there is more
than one house wire to connect to the two fan lead wires, consult
an electrician for the proper size wire connectors to use.
Important:
Be sure wiring box is properly grounded or that a
ground (green or bare) wire is present.
1.
Choose wiring diagram [Fig. 1A, Fig. 1B or Fig. 1C] that fits your
situation and make appropriate wiring connections as follows: (
Make
special note of Step 3 on the following page while wiring.
)
1A.
Connect
BLACK
and
BLUE
wire from fan to
BLACK
wire
from ceiling with wire connector (N) provided. Connect
WHITE
wire from fan to
WHITE
wire from ceiling with wire connector (N)
provided. Connect all
GROUND
(
GREEN
) wires together from fan
to
BARE
/
GREEN
wire from ceiling with wire connector (N)
provided. [Fig. 1A]
1B.
If you intend to control the fan light with a separate wall
switch, wire as indicated in the instructions in 1A
except
connect
BLUE
wire from fan to the
BLACK
supply from the independent
switch. [Fig. 1B]
1C.
If you intend to control the fan and light with separate wall
switches, wire as indicated in the instructions in 1A
except
connect
BLUE
wire from fan to the
BLACK
supply from the
independent wall switch for the light and connect
BLACK
wire
from fan to the
BLACK
supply from the other independent wall
switch for the fan. [Fig. 1C]
Warning:
If house wires are different colors than referred to
in following steps, stop immediately. A professional electrician is
recommended to determine wiring.
BLACK
BLUE
A
F
B
C
A
Ball
Hanging
Ball
Set
Screw
FAN AND LIGHT CONTROLLED BY CHAIN.
BLACK (POWER)
WHITE (NEUTRAL)
GROUND
GROUND
WHITE
Fig. 1A
BLACK
BLUE