background image

- 16 - 

- 17 - 

•  With the help of the Park Tool IR-1�2 or 

the RockShox Barb Connector, the cable 
housing including the foam tube can be 
guided through the down tube and into the 
left-hand cable hole at the top of the tube�

Brake hose routing

In order to simplify the routing of the brake 
hose, the frame comes with a cable housing 
inside the left-hand chain stay� The Park 
Tool IR-1�2 or the RockShox Barb Connector 
may help further�

Bremsleitung

SRAM Leitungs- 

Verbinder

50 cm  

Einfädelhilfe

At first, the hose is to be cut at the brake 
lever� The clamping capsule and the fitting 
need to be removed�

Working with the Park Tool Internal Cable 
Routing Kit:  

•  Connect the front end of the cable housing 

in the left-hand chain stay with the 
threaded end part of the routing advice�

•  Towards the rear end of the frame, pull the 

cable housing out of the chain stay leaving 
the Park Tool routing advice inside the 
chain stay�

•  Disconnect the advice and the cable 

housing� 

•  Connect the threaded part of the advice 

to the brake hose for the rear brake 
and pull it back into the left-hand chain 
stay� Support the hose and the tool by 
simultaneously pulling and pushing� 

•  Guide the routing advice through the left-

hand hole of the main frame and from the 
bottom into the ServicePort� 

•  Slip a foam tube over the routing advice 

and the brake hose�

•  With the help of the Park Tool magnet, 

guide the routing advice through the down 
tube of the frame and into the top end 
cable hole of the frame�

If you assemble your bike without a 
Park Tool Internal Cable Routing Kit, the 
procedure can be realized with a SRAM hose 
connector, too� In the end, the brake hose 
can be guided through the chain stay in a 
similar way as with the Park Tool advice� 

The assembly of the brake depends on 
different brake modals and should be 
realized as displayed below�

Picture shows rear brake on a Post Mount socket with hose 
routing for Shimano.

Picture shows rear brake on Post Mount socket with hose 
routing for SRAM.

Содержание 601 Mk4
















Отзывы: