Liquivision XEN Скачать руководство пользователя страница 64

Страница: 64 / 84

Dive Computer

User Manual

Liquivision Products, Inc

Revision 3.2 Software 2.58

WARNING

THESE BATTERIES ARE THE

ONLY

AUTHORIZED BATTERIES

Please note that only ER14335M, ER17335M, LFP123A, LiFeP04 and ICR16340 batteries are

authorized for use with your XEN.

ER14335 or ER17335 batteries (no M) are NOT compatible.

Only the batteries contained in Liquivision battery packs can be guaranteed to perform to Liquivision

standards. Use of other batteries could lead to inaccurate battery meter readings, and if the battery

reading is not accurate, you could be diving your XEO on an empty battery without knowing it. This

could lead your XEO to turn off unexpectedly leading to a loss of critical dive information.

As of April 1

, 2013, ICR16340 and LiFeP04 (Tenergy) batteries are no longer being sold in battery

packs. They have been replaced by the LFP123A (K2) batteries.

Be safe! Use Only Approved Batteries!

Set Your XEN To the Correct Battery Type To Get Accurate Battery Meter Reading!

We strongly recommend always having a spare battery on hand, since spare batteries have a long shelf
life and do not require any special storage environment (just dry and away from direct sunlight or heat).

Spare batteries are sold as follows:

•

Disposable Battery 1-Pack



1 disposable battery (ER14335M or ER17335M)



1 spare O-ring

•

Disposable Battery 3-Pack



3 disposable batteries (ER14335M or ER17335M)



3 spare O-rings



1 reseal-able tube of O-ring lubricant

•

Charger Kit



Charger



AC Adapter with international plug adapters



2 rechargeable batteries (LFP123A)



5 spare O-rings



1 reseal-able tube of O-ring lubricant

•

Rechargeable Battery 2-Pack



2 rechargeable batteries (LFP123A)



5 spare O-rings



1 reseal-able tube of O-ring lubricant

Содержание XEN





















































































Результаты поиска

Содержание XEN

Отзывы:

Похожие инструкции для XEN

Бренды по названию

Популярные бренды

Liquivision XEN, Руководство пользователя

Результаты поиска

Содержание XEN

Отзывы:

Похожие инструкции для XEN

Бренды по названию

Популярные бренды