Page 19
Page 18
ANTENNA CONSIDERATIONS
The choice of antennas is a critical
and often overlooked design
consideration. The range,
performance, and legality of an RF link
are critically dependent upon the
antenna. While adequate antenna
performance can often be obtained by
trial and error methods, antenna
design and matching is a complex
task. A professionally designed
antenna, such as those from Linx, will
help ensure maximum performance and FCC compliance.
Linx transmitters are capable of achieving output power in excess of some legal
limits. This allows the designer to use an inefficient antenna, such as a loop trace
or helical, to meet size, cost, or cosmetic requirements and still achieve full legal
output power for maximum range. If an efficient antenna is used, then some
attenuation of the output power will likely be needed. This can easily be
accomplished by using the LADJ line or a T-pad attenuator. For more details on
T-pad attenuator design, please see Application Note AN-00150.
A receiver antenna should be optimized for the frequency or band in which the
receiver operates and to minimize the reception of off-frequency signals. The
efficiency of the receiver’s antenna is critical to maximizing range performance.
Unlike the transmitter antenna, where legal operation may mandate attenuation
or a reduction in antenna efficiency, the receiver’s antenna should be optimized
as much as is practical.
It is usually best to utilize a basic quarter-wave whip until your prototype product
is operating satisfactorily. Other antennas can then be evaluated based on the
cost, size, and cosmetic requirements of the product. You may wish to review
Application Note AN-00500 “Antennas: Design, Application, Performance” and
Application Note AN-00501 “Understanding Antenna Specifications and
Operation.”
Figure 27: Linx Antennas
GENERAL ANTENNA RULES
The following general rules should help in maximizing antenna performance.
1. Proximity to objects such as a user’s hand, body, or metal objects will cause an
antenna to detune. For this reason, the antenna shaft and tip should be
positioned as far away from such objects as possible.
2. Optimum performance will be obtained
from a 1/4- or 1/2-wave straight whip
mounted at a right angle to the ground
plane. In many cases, this isn’t desirable
for practical or ergonomic reasons, thus,
an alternative antenna style such as a
helical, loop, or patch may be utilized
and the corresponding sacrifice in performance accepted.
3. If an internal antenna is to be used, keep it away from other metal components,
particularly large items like transformers, batteries, PCB tracks, and ground
planes. In many cases, the space around the antenna is as important as the
antenna itself. Objects in close proximity to the antenna can cause direct
detuning, while those farther away will alter the antenna’s symmetry.
4. In many antenna designs, particularly 1/4-wave
whips, the ground plane acts as a counterpoise,
forming, in essence, a 1/2-wave dipole. For this
reason, adequate ground plane area is essential.
The ground plane can be a metal case or ground-fill
areas on a circuit board. Ideally, it should have a
surface area > the overall length of the 1/4-wave
radiating element. However, this is often not
practical due to size and configuration constraints.
In these instances, a designer must make the best
use of the area available to create as much ground
plane as possible in proximity to the base of the antenna. In cases where the
antenna is remotely located, or the antenna is not in close proximity to a circuit
board, ground plane, or grounded metal case, a metal plate may be used to
maximize the antenna’s performance.
5. Place the antenna as far as possible from potential interference sources. Any
frequency of sufficient amplitude to enter the receiver’s front end will reduce
system range and can even prevent reception entirely. Switching power
supplies, oscillators, or even relays can also be significant sources of potential
interference. The single best weapon against such problems is attention to
placement and layout. Filter the module’s power supply with a high-frequency
bypass capacitor. Place adequate ground plane under potential sources of noise
to shunt noise to ground and prevent it from coupling to the RF stage. Shield
noisy board areas whenever practical.
6. In some applications, it is advantageous to
place the module and antenna away from the
main equipment. This can avoid interference
problems and allows the antenna to be
oriented for optimum performance. Always use
50
Ω
coax, like RG-174, for the remote feed.
NUT
GROUND PLANE
(MAY BE NEEDED)
CASE
Figure 30: Remote Ground Plane
OPTIMUM
USEABLE
NOT RECOMMENDED
Figure 28: Ground Plane Orientation
I
E
DIPOLE
ELEMENT
GROUND
PLANE
VIRTUAL
λ
/4
DIPOLE
λ
/4
λ
/4
VERTICAL
λ
/4 GROUNDED
ANTENNA (MARCONI)
Figure 29: Dipole Antenna
