6
a.
When the power-supply cord or plug is damaged.
b.
If liquid has been spilled, or objects have fallen onto the product.
c.
If the product has been exposed to rain or water.
d.
If the product does not operate normally by following the operating instructions [included with the product]. Adjust only those controls that are
covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the product to its normal operation.
e.
If the product has been dropped or the cabinet has been damaged.
f.
If the product exhibits a distinct change in performance.
17.
Replacement Parts
–
If replacement parts are necessary, have a Low-Voltage Electrician replace them using only part specified by the manufacturer.
Unauthorized substitutions may result in fire, electric shock or other hazards. Replacement parts can be found at
https://www.linortek.com/store/
18.
Safety Check
–
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
19.
Coax Grounding
–
If an outside cable system is connected to the product, be sure the cable system is grounded. U.S.A. models only
–
Section 810 of the
National Electrical Code, ANSI/NFPA No.70-1981, provides information with respect to proper grounding of the mount and supporting structure, grounding
of the coax to a discharge product, size of grounding conductors, location of discharge product, connection to grounding electrodes, and requirements for
the grounding electrode.
20.
Lightning
–
For added protection of this product during a lightning storm, or before leaving it unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
21.
Outdoor Use
–
This product is not waterproof and should not be allowed to get wet. Do not expose to rain or other types of liquid. Do not leave out-of-
doors overnight as condensation may occur.
22.
While changing batteries, fuses or handling a board level product be careful of electrostatic discharge which can damage electronic devices. It is best to
use a grounded electronics service bench. If this is not available you can discharge yourself by touching a metal appliance or pipe. While changing the
batteries or fuses do not touch i) any wires other than the battery wires and ii) the printed circuit board.
LIMITATION OF LIABILITY
IN NO EVENT WILL LINOR TECHNOLOGY BE LIABLE, WHETHER IN CONTRACT, TORT, OR OTHERWISE, FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL OR
PUNITIVE DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, OR LOST PROFITS,
SAVINGS, OR REVENUES TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.
DISCLAIMER FOR CRITICAL APPLICATIONS
This product is not intended or authorized for life support product or for other uses for which a failure could cause personal injury or death. If you or your customers
use or permit the use of this product for such unintended or unauthorized uses, you agree to fully indemnify Linor Technology and its affiliates, and the officers,
employees and distributors of each, from all liability related to such use, including attorneys’ fees and costs.
FURTHER NOTICE FOR LIMITATION OF USE
Unless specifically stated, our Products are NOT designed to switch line voltage (110V and above) devices. To control device that operate at line voltages a qualified
electrician MUST install an intermediary device such as a relay. When choosing devices to control, it is best to select low voltage controls such as a 24VAC solenoid to
water flow control. Only qualified electricians may wire a line voltage device. Additionally, local codes must be followed including but not limited to wire gauge size
and suitable housing. Linortek assumes no responsibility for harm to the user or third parties for improperly using our Products. This liability remains with the user.
Linortek assumes no responsibility for damage to the device due to improperly using our Products.
RELAY VOLTAGE SPECIFICATIONS
Please use caution when connecting devices to electrical circuits or other equipment. This web controller is NOT designed to connect to any voltage greater than 48V.
If you want the product to control Line Voltage products and devices, refer to Diagram 1 below. Utilizing this arrangement, should allow you to virtually control
anything. It is important that you use licensed electricians and comply with electrical codes that are applicable to your location. These codes exist for your safety, as
well as the safety of others. Linortek assumes no responsibility for any harm or damage resulting from a failure adhere to local laws, ordinances or regulations or
failure to follow specified instructions for installation and product usage.