Linn KELTIK Скачать руководство пользователя страница 49

Страница: 49 / 65

Page 49

Revised Dec 97

Index

SARA HISTORY

Introduced

1978

Discontinued

1989

Upgrade

Date Serial No.

Crossover:
Bi-wiring introduced to Sara 9

Oct. 1988

20,913/4

Sara 9:
Introduced, incorporating changes
to treble unit (countersunk screws),
bass unit (white disc removed and
plastic surround changed to
thicker rubber), crossover (now 4
ohm)

Sept. 1987 18,299/300

Sockets:
Replaced cannon sockets with
two 4 mm sockets.

Jun. 1985

16,300/1

Bass Unit:
Surround changed to plastic
material.

May 1985

16,051/2

Treble Unit:
Smoother response. Incorporates
Linn logo on front plate.

May 1984

14,731/2

Crossover:
Resistor added in parallel with
treble coil.

Feb. 1983 13,249/50

Unit Damping:
Painted with sound deadening paint.
Cabinet Material:
Material change; now has rounded
front.

Mar. 1982

10,850/1

Drive Unit:
Sealer changed from mastic to
silicone sealant.

Jan. 1980

10,440/1

Baffle:
Changed from welded plastic to
one piece moulded carbon filled ABS
with removable ring for front bass
unit. Bass unit venting increased.

Oct. 1979 10,280/81

LOUDSPEAKER HISTORY

Содержание KELTIK

































































Результаты поиска

Содержание KELTIK

Отзывы:

Похожие инструкции для KELTIK

Бренды по названию

Популярные бренды

Linn KELTIK, Руководство пользователя

Результаты поиска

Содержание KELTIK

Отзывы:

Похожие инструкции для KELTIK

Бренды по названию

Популярные бренды