background image

14

Chapter 3: Installation
Installing the Switch

 

RPS1000—Business Series 380W RPS Unit Installation & Administration

Chapter

3

Four Phillips machine screws for attaching the brackets to a rack

Installing the Switch

This section describes these installation procedures:

• Table or Shelf-Mounting, page 14

• Rack-Mounting,  page 14

Table or Shelf-Mounting

Follow these steps to install your chassis on a table or shelf:

1. Unpack the RPS1000.

2. Attach the rubber feet from the accessory kit into the round recesses that are located on the 

bottom of the chassis.

3. Place the RPS1000 chassis on an appropriate table, shelf, or desktop.

Rack-Mounting 

To install the chassis in a 19-inch or 24-inch rack, follow the instructions described in these 
procedures.

WARNING: 

Do not stack the chassis on any other 

equipment. If the chassis falls, it can cause severe bodily 
injury and equipment damage.

NOTE: 

If you have questions or need assistance, see the 

Appendix C, "Linksys Contact Information," section

.

NOTE: 

A 24-inch rack requires optional mounting 

hardware.

Содержание SFE2000P - Managed Ethernet Switch































Отзывы: