Link Research L2102 Скачать руководство пользователя страница 6

Страница: 6 / 48

Link XP L2102/L2104 Receiver Instruction Manual Issue 1 - October 2003 Page 6 of 48
Link Research Ltd. 23/24 Watford Metro Centre, Dwight Road, Watford, Hertfordshire, WD18 9XA, England. Tel: +44 (0) 1923 200 900
Registered in London No. 2074604

Web:

www.linkres.co.uk Fax: +44 (0) 1923 241 357

L2102 & L2104 Receiver

Instruction Manual

Do not subject the equipment to splashing or dripping liquids.
Only authorised trained personnel should open the product. There are no functions

that require the User to gain access to the interior of the product.

5.2 Safety

This equipment has been designed to meet the requirements of the following:-

EN60950

European Safety of information technology equipment including

business equipment.

IEC 60950 International Safety of information technology

equipment including business equipment.

UL 1950USA Safety of information technology equipment including

business equipment.

The equipment has been designed to meet the following:-

55022 European

Emission

Standard equipment-class A.

EN 55103-2

European

Generic Immunity Standard.

FCC

USA

Conducted and radiated emission limits
For a Class A digital device

ETSI EN301 - 489 - 3

For Radio Equipment in the range of 1GHz to
40GHz.

5.3 Radio

ETSI EN300 - 440 -1

For Radio Equipment in the range of 1 GHz to

40GHz

5.4 CE Marking

The CE mark is affixed to the LinkXP and the EC Declaration of Conformity and the
Technical File is available on request.

5.5 Other Compliance Notes

Antistatic precautions should be observed when connecting leads to the rear panel

connectors.

Nominal lead length used for EMC checks was less than 3 metres.

Содержание L2102

















































Результаты поиска

Содержание L2102

Отзывы:

Похожие инструкции для L2102

Бренды по названию

Популярные бренды

Link Research L2102, Инструкция по эксплуатации

Результаты поиска

Содержание L2102

Отзывы:

Похожие инструкции для L2102

Бренды по названию

Популярные бренды