background image

 

  

 

AirFinder Quick Start Guide

 

12 

6.

 

FCC Warning 

 

Federal Communications Commission (FCC) Interference Statement

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications.

 

However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the interference by one of 
the following measures:

 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

Consult the dealer or an experienced radio/TV technician for help.

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

 

(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

 

FCC Caution: Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user's authority to operate this equipment. 

 

RF exposure warning 

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Содержание AirFinder 3.0















Отзывы: