Linhai T-Boss 550 Скачать руководство пользователя

Страница: 101 / 258

CHAPTER 3 ENGINE

T-Boss550 SERVICE MANUAL20.0

CHAPTER 3 ENGINE PAGE. 3- 76

Front Output Shaft

Check bearing 7 for smooth turning and abnormal

wear. Check oil seal 5 for damage.

Wear or damage:

→

Replace

Apply lubrication oil to bearing 7 and oil seal 5 lip
before assembly.

Apply thread locker to bearing limit nut 6 (left thread)
and tighten to the specified torque.

Bearing limit nut Tightening torque: 80

N•m

Tighten Nut 1 to the specified torque
Front output shaft nut tightening torque: 97

N•m

Driven Bevel Gear

Remove nut 19, washer 18, coupler 17 and oil seal 16.

Protect end thread of driven bevel gear with proper
device

②

. Fix bevel gear cover 14 and press out

driven bevel gear.

Place a clean rag

①

under bevel gear cover.

Remove bearing limit nut 10 with special tool

②

and

remove bearing.

Check driven bevel gear 8 surface for scratches,
wear. Scratch or wear:

→

Replace

Check free turning of bearing 9 and 11. Replace
with a new one if any abnormal is found.

Use new oil seal 16 and O-ring 12 when
assembling.

Adjust washer 13 if any of right crankcase, driven
bevel gear 8 or driven bevel gear cover 14 is

replaced. Refer to bevel gear adjustment for

details.

Apply lubrication oil to bearing 9 and 11 and oil seal
16, O-ring. Apply thread locker to nut 10 and tighten

to the specified torque.

Tightening torque :110

N•m

Tool: driven bevel gear nut wrench

Driven bevel gear nut tightening torque:150

N•m

Bevel Gear Washer Adjustment

Adjust washer

①

and

②

when replacing crankcase

and/or bevel gear and/or bevel gear cover,

Содержание T-Boss 550



































































































































































































































































Результаты поиска

Содержание T-Boss 550

Отзывы:

Похожие инструкции для T-Boss 550

Бренды по названию

Популярные бренды

Linhai T-Boss 550, Руководство по обслуживанию

Результаты поиска

Содержание T-Boss 550

Отзывы:

Похожие инструкции для T-Boss 550

Бренды по названию

Популярные бренды