background image

18

OPERATIVE MODE

In the standard mode of operation, the function in which the 

mains is present

 and in case it fails is ensured l 'battery power. 

In the standard mode of operation, the function in which the 

 and in case it fails is ensured l 'battery power. 

 and in case it fails is ensured l 'battery power. 

In this function, the display looks like fi gure below. it is shown

 this line

 is 

INV.

 and battery.

In this function, the display looks like fi gure below. it is shown

 is 

 and battery.

In this function, the display looks like fi gure below. it is shown

 is 

 and battery.

In this function, the display looks like fi gure below. it is shown

 is 

 and battery.

In this function, the display looks like fi gure below. it is shown

 is 

 and battery.

The load level shows the signaling load capacity connected:

1) If the battery box is present and the presence of network (line) flashes, means that the voltage or frequency of the 
main electricity grid has exceeded the nominal range.

2) If the 'output is higher than the ranges indicated, the output load LED will be turned on and an acoustic signal alternating beep per 

second will be present.

In this case it will be necessary to remove output loads one by one fi no to arrive at a minor load of 90% of the nominal one.

BATTERY MODE

In battery mode, the display shows' icon 

BATTERY

 is 

INV

 lit as in fi gure below. The battery capacity is visible 

through the scale of the battery level.

1) When the CPS works in battery mode, the buzzer will sound every 4 seconds. if the function key is pressed for more 
than one second, the machine goes into silent mode. Pressing the button again reactivates the same way the 'alarm.

2) When the battery capacity decreases, the number of capability indicators decrease. If the voltage drops below the operating 
threshold, the 'alarm sounds every second and the red ALARM LED flashes to remind the' user that the battery capacity is 
running low fi lthough the CPS does not get to go off automatically.

CHAPTER 6

Содержание Spy Center Basic SCB010

































Отзывы: