Linear Technology LTC6804-1 Скачать руководство пользователя страница 62

Страница: 62 / 78

LTC6804-1/LTC6804-2

680412fc

For more information

www.linear.com/LTC6804-1

applicaTions inForMaTion

CELL BALANCING WITH INTERNAL MOSFETS

The S1 through S12 pins are used to balance battery cells.

If one cell in a series becomes overcharged, an S output

can be used to discharge the cell. Each S output has an

internal N-channel MOSFET for discharging. The NMOS

has a maximum on resistance of 20Ω. An external resistor

should be connected in series with the NMOS to dissipate

heat outside of the LTC6804 package as illustrated in

Figure 35. It is still possible to use an RC to add additional

filtering to cell voltage measurements but the filter R must

remain small, typically around 10Ω to reduce the effect

on the programmed balance current. When using the

internal MOSFETs to discharge cells, the die temperature

should be monitored. See Power Dissipation and Thermal

Shutdown section.

CELL BALANCING WITH EXTERNAL MOSFETS

The S outputs include an internal pull-up PMOS transistor.

The S pins can act as digital outputs suitable for driving

the gate of an external MOSFET. For applications requiring

high battery discharge currents, connect a discrete PMOS

switch device and suitable discharge resistor to the cell,

and the gate terminal to the S output pin, as illustrated in

Figure 36. Figure 34 shows external MOSFET circuits that

include RC filtering.

Figure 35. Internal Discharge Circuit

Figure 36. External Discharge Circuit

Table 47. Discharge Control During an ADCV Command with DCP = 0

CELL MEASUREMENT PERIODS

CELL CALIBRATION PERIODS

CELL1/7 CELL2/8 CELL3/9 CELL4/10 CELL5/11 CELL6/12 CELL1/7 CELL2/8 CELL3/9 CELL4/10 CELL5/11 CELL6/12

DISCHARGE

PIN

to t

OFF

S10

OFF

S11

OFF

S12

OFF

LTC6804

680412 F35

FILTER

DISCHARGE

C(n)

S(n)

C(n – 1)

LTC6804

680412 F36

BSS308PE

3.3k

C(n)

S(n)

C(n – 1)

DISCHARGE CONTROL DURING CELL

MEASUREMENTS

If the discharge permited (DCP) command bit is high in a

cell measurement command, then the S pin discharge states

are not altered during the cell measurements. However, if

the DCP bit is low, any discharge that is turned on will be

turned off when the corresponding cell or adjacent cells

are being measured. Table 47 illustrates this during an

Содержание LTC6804-1















































































Результаты поиска

Содержание LTC6804-1

Отзывы:

Похожие инструкции для LTC6804-1

Бренды по названию

Популярные бренды

Linear Technology LTC6804-1, Руководство пользователя

Результаты поиска

Содержание LTC6804-1

Отзывы:

Похожие инструкции для LTC6804-1

Бренды по названию

Популярные бренды