background image

Copyright © 2005 Linear Corporation 

221660

 A

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and 
workmanship for twenty-four (24) months. The Warranty Expiration 
Date is labeled on the product. This warranty extends only to 
wholesale customers who buy direct from Linear or through Linear’s 
normal distribution channels. Linear does not warrant this product to 
consumers. Consumers should inquire from their selling dealer as to 
the nature of the dealer’s warranty, if any. 

There are no obligations 

or liabilities on the part of Linear LLC for consequential damages 
arising out of or in connection with use or performance of 
this product or other indirect damages with respect to loss of 
property, revenue, or profi t, or cost of removal, installation, or 
reinstallation.

 

All implied warranties, including implied warranties 

for merchantability and implied warranties for fi tness, are valid only 
until Warranty Expiration Date as labeled on the product. 

This 

Linear LLC Warranty is in lieu of all other warranties express 
or implied.

All products returned for warranty service require a Return Product 
Authorization Number (RPA#). Contact Linear Technical Services at 
1-800-421-1587 for an RPA# and other important details.

IMPORTANT WIRELESS INFORMATION

Linear radio controls provide a reliable communications link and fi ll 
an important need in portable wireless signaling. However, there are 
some limitations which must be observed.

•  For U.S. installations only: The radios are required to comply with FCC 

Rules and Regulations as Part 15 devices. As such, they have limited 
transmitter power and therefore limited range.

•  A receiver cannot respond to more than one transmitted signal at a 

time and may be blocked by radio signals that occur on or near their 
operating frequencies, regardless of code settings.

•  Changes or modifi cations to the device may void FCC compliance.

•  Infrequently used radio links should be tested regularly to protect 

against undetected interference or fault.

•  A general knowledge of radio and its vagaries should be gained prior 

to acting as a wholesale distributor or dealer, and these facts should be 
communicated to the ultimate users.

FCC NOTICE

Changes or modifi cations not expressly described in this manual 
or approved by the manufacturer could void the user’s authority to 
operate the equipment.
This equipment has been tested and found to comply with the limits 
for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there 
is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and receiver.

•  Connect the equipment into an outlet on a circuit different from that to 

which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Содержание RE-2





























Отзывы: