background image

  

Forward Path Set-up

)

 :  

(Refer to Figure 7) 

1.

Verify that the received optical level indicated on the “Optical Rx LED “ strip is as expected. 

2.

The Optical node comes factory set with attenuators already in place.  The attenuator used to 
establish the output tilt is factory set with a 9dB attenuator.  That will produce approximately 12-13db 
of tilt between 54 and 1000MHz. That indicates there is approximately 3 

– 4dB of built in equalization.  

3.

While monitoring the forward 

Out1

 test point (-20dB),  and with a 0dB pad in 

ATT3

 position, place 

desired attenuator value into EQ1 for desired output tilt.  

4.

Countinuing to monitor 

Out1

 test point (-20dB), adjust pad value in 

ATT3

 position for the desired 

output level.  Verify that the level is correct at both ends of the bandwidth.   Output 1 & 2 are now set 
up in the Forward Path. 

5.

Repeat steps 3 & 4 for Output 3 & 4, using test point on 

Out3

, and 

ATT4

 and 

EQ2

 positions. 

 

Downstream 

Incoming Fiber 

ATT4; Fwd RF 
attenuator 

ATT3; Fwd RF 
attenuator 

EQ2; Fwd 
Equalizer For 
Port 3&4; Tilt set 
with  attenuator 

EQ1; Fwd Equalizer For Port 
1&2; Tilt set with  attenuator 

Optical RX LED 
Display TP 

Figure 7 

User Manual 

LBON4000 

LBON4000 April 2013 

Содержание LBON4000 ONU












Отзывы:

Похожие инструкции для LBON4000 ONU