Lincoln IDEALARC DC-400 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

background image

IMA 474

DC-400

Page 13

2) DC-400 is used with an LN-22 equipped with an older

K279 Contactor-Voltage Control Option. Eliminates
electrode overrun when gun trigger is released. Not
required when later K279 (above Code 8800) is used.

3) DC-400 is used with any semiautomatic wire feeder and

possible small spark, if electrode touches work just after
gun trigger is released, is objectionable.

HI-FREQUENCY KIT

(K799-1 OR K930-2)

Kit supplies the high frequency plus gas valve for DC TIG
welding. The DC-400 is shipped with proper R.F. bypass
circuitry installed to protect the control circuit when welding
with a HI-FREQ unit. K844 Water Valve Option Kit can be
used with K799-1 when TIG welding with water cooled
torches. K844-1 Water Valve Option Kit can be used with
K930-2 when welding with water cooled torches.

OPTIONAL AMPTROL ADAPTER FOR K799-1 HI-
FREQUENCY KIT (K915-1 REQUIRES K864
ADAPTER OR K843 ADAPTER)

A “V” cable to connect a K799-1 Hi-Freq kit (5-pin
connector) with either a K963 Hand Amptrol or a K870 Foot
Amptrol (6-pin connector) and the machine.

The cable

going to the machine has a 6-pin connector which requires
either a K864 adapter to connect with the 14-pin connector
on the machine or a K843 adapter to connect to terminals
75, 76, 77 and the case grounding screw on the machine.

UNDERCARRIAGES

KA1236 - Basic Undercarriage

KA1237 - Basic undercarriage with gas bottle

support.

For easy moving of the machine, optional undercarriages
are available.

Install per instructions provided with undercarriage.

TECHNICAL SPECIFICATIONS

Note:

CVI mode draws more input current than CVS or CC modes.

Model

DC-400

Type

KA1369-3

KA1369-1

KA1369-2

Frequency

50/60Hz

Output Rating

DC

Amperes

500 450 400

Volts

40 38 36

Duty Cycle

50% 60% 100%

Output Range

Min.

60A 12V CV (22V CC)

Max.

500A 42V CC, CV

Max. O.C.V.

57 CC (45.5 CVI)

Input Ratings

Standard Voltages

50/60Hz

50Hz

60Hz

50/60Hz

415V

220V

230V

380V

380 V

380V

500V

440V

460V

Rated Input Current

73A

63A

42A

to AS1966-1

39A

42A

39A

32A

37A

32A

Maximum Input Current

113A

97A

65A

under normal operating

60A

65A

58A

50A

conditions

56A

48A

Additional Features

Amptrol Adapter Cable

Yes

115V Starter Circuit

Standard

Suitable Undercarriages

Yes

Remote Output Control

Yes

Other Features

Stackable Case

Weight approx.

215kg

Dimension Print

M12244-7

Wiring Diagram

AL2460

ARC WELDING SUPPLIES - 07 847 7870

«
...
11
12
13
14
15
...
»

Содержание IDEALARC DC-400





















































Отзывы:

Нет отзывов

Похожие инструкции для IDEALARC DC-400

Бренд: iDance Страницы: 25

Бренд: Radio Shack Страницы: 16

ABICAR 1200 PRO

Бренд: Abicor Binzel Страницы: 64

Art Series ART500

Бренд: Mackie Страницы: 2

Бренд: TCL Страницы: 16

Бренд: ZKTeco Страницы: 16

X Wireless Series

Бренд: Axess Страницы: 8

Бренд: Tokai Страницы: 20

Бренд: HAKO Страницы: 6

Soundgear Series

Бренд: JBL Страницы: 73

Бренд: ubbink Страницы: 61

Бренд: SANJIANG Страницы: 8

OILPRESS 180.902

Бренд: WILHELM KELLER Страницы: 4

Бренд: Q-See Страницы: 9

PYTHON-PLUS K2447-1

Бренд: Lincoln Electric Страницы: 39

IMI SENSORS Y683A101001

Бренд: PCB Piezotronics Страницы: 30

Бренд: Car-O-Liner Страницы: 92

Бренд: Quality Heating Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды