Lincoln Electric INVERTEC 175TP Скачать руководство пользователя страница 15

English 13 English 

WEEE 

07/06 

En

g

lish

 

Do not dispose of electrical equipment together with normal waste! 
In observance of European Directive 2012/19/UE on Waste Electrical and Electronic Equipment (WEEE) 
and its implementation in accordance with national law, electrical equipment that has reached the end of 
its life must be collected separately and returned to an environmentally compatible recycling facility.  As 
the owner of the equipment, you should get information on approved collection systems from our local 
representative. 
By applying this European Directive you will protect the environment and human health! 

 

Spare Parts 

12/05 

Part List reading instructions 

  Do not use this part list for a machine if its code number is not listed.  Contact the Lincoln Electric Service 

Department for any code number not listed. 

  Use the illustration of assembly page and the table below to determine where the part is located for your particular 

code machine. 

  Use only the parts marked "X" in the column under the heading number called for in the assembly page (# indicate 

a change in this printing). 

 
First, read the Part List reading instructions above, then refer to the "Spare Part" manual supplied with the machine, that 
contains a picture-descriptive part number cross-reference. 
 

Authorized Service Shops Location 

09/16 

  The purchaser must contact a Lincoln Authorized Service Facility (LASF) about any defect claimed under Lincoln's 

warranty period. 

 Contact your local Lincoln Sales Representative for assistance in locating a LASF or go to 

www.lincolnelectric.com/en-gb/Support/Locator.

 

 

Electrical Schematic 

 
Refer to the "Spare Part" manual supplied with the machine 
 

Accessories 

 
Consult the area agents or the dealer. 
 

Содержание INVERTEC 175TP
















Отзывы: