background image

7

M

ad

e i

n t

he U

SA

Inner  Rail x 1

Outer Rail x 1

Cantilever x 2

2

Foot x 2

Leveler for 

Foot x 4

Control Box x 1

Motor 

Cable x 2

Tapping 

10-12 x 2" 

Tapping 

M6 x 16 mm 

PACKING LIST

Kick Lock x 2

Screw x 13-20

8-15 x 0.75”

Clamp x

Desk Switch

Desk Leg x 2

Mains Cable x 1

Screw x 2

Allen Bolt x 8

PRODUCT RATINGS

Application of the DESKLINE

® 

DL5/6 system: 

 

Irrespective of the load the 

duty cycle 10% ~ 2 

minutes of continuous use at full load, followed 

by 18 minutes of pause 

stated in the data sheets, must 

NOT 

be exceeded as this will result in super heating of the 

motor, the brake and the spindle nut. Exceeding the duty 

cycle will result in a dramatic reduction of the life of the 

system.  

 

This product is inteded for indoor use only.

Weight limit for two-leg DL5/6 desk: 1600N (363 lbs 
including weight of the desk top.  
 
Kick & Click Fixed Frame: Fits desks with 47.25”+ tops. 
(Actual frame width of 44.9”) 
 
Kick & Click Large Adjustable Frame: Fits desks from 54” to 
84” (actual frame width of 52.75” to 76.3”). 

Kick & Click Short Adjustable Frame: Fits desks from 41” to 
60” (actual frame width of 38.25” to 50”).

Содержание Desk Frame 1

























Отзывы: