background image

Ersatzteile für klassische britische Fahrzeuge

Fitting instruction for the Mitsuba fuel pump 

(Part. no. 14976)

Installation guide for electric fuel pump

MITSUBA Electric Fuel Pump is designed to be installed on carburetor type of vehicles.
The fuel comes in through the inlet pipe and the strain er element, then pumped forward 
to carburetor through the outlet pipe.

Features

Operates on car battery and can be installed easily.
Light weight and compact; positive fuel delivery permits quick acceleration.
This pump is suited to install on the car under approximately 3,000 c.c. engine.
Starts pumping immediately as the power switch is turn ed on.
Reduced power consumption and pumps fuel more fre quently when you drive fast; less 
often at low speeds. Solenoid operation eliminates fire hazards and extends pump life.
Built-in filter keeps dust out and adds to pump and engine life.

Operating principle

The Fuel Pump consists of Relay mechanism, Solenoid mechanism, Pump and Strainer 
mechanism.
Relay mechanism is hermetically sealed.
A magnet and a plunger spring give vertical motion to the plunger and consequently to 
the piston whereto the plunger is connected. This action pumps up the fuel.

Rated voltage 12V

Lowest starting voltage under 7.0V

Service voltage 10~15V

Pressure (kg/cm

2

)  0.30 +/- 0.03 

Closed outlet (lbs inch

2

) 4.26 +/- 0.40

Maximum outlet gal/min / cc/min 1,500 / 0.40

Current (average) (A) 1.0

Weight (gr)  1,120 

(lbs) 2.5

150 mm

101 mm

56 mm

65 mm

Plunger

Kontakt

Magnet

Spring

Piston

Filter

Inlet

Outlet

LIMORA main offi ce

Industriepark Nord 19-21
D - 53567 Buchholz

Jaguar:   

+49 (0) 26 83 - 70 61

Triumph:  

70 62

Mini:  

70 

63

MG:  

70 

64

Austin Healey: 

70 65

Fax:  

70 

59

E-mail:  

[email protected]

Limora Aachen

Feldstraße 41
D - 52070 Aachen
Tel: 

 

+49 (0) 241 - 55 939 0

Fax: 

 

+49 (0) 241 - 55 939 20

E-mail:  

[email protected]

Nous parlons français
Wij spreken nederlands

Limora Berlin

Wiebestraße 36-37
D - 10553 Berlin
Tel: 

 

+49 (0) 30 - 25 93 92 30

Fax: 

 

+49 (0) 30 - 25 93 92 33

E-mail: 

 [email protected]

Limora Düsseldorf

Harffstraße 110a
D - 40591 Düsseldorf
Tel: 

 

+49 (0) 211 - 98 471 01

Fax: 

 

+49 (0) 211 - 98 471 08

E-mail:   [email protected]

Limora Stuttgart

Graf-Zeppelin-Platz 1

(Wolfgang-Brumme-Allee 55)

D - 71034 Böblingen
Tel: 

  +49 (0) 70 31 - 306 95 10

Fax: 

  +49 (0) 70 31 - 306 95 12

E-mail:   [email protected]

Limora Hamburg

Hauptstraße 49 /
Bl. Chaussee
22869 Hamburg-Schenefeld
Tel: +49 

(0) 40 - 553 53 15

Fax: +49 

(0) 40 - 55 77 32 38

E-Mail: [email protected]

Limora Paris

Tel: 

 

+33 (0) 139 - 570 599

Fax: 

 

+33 (0) 139 - 570 699

Limora Polska

E-mail:   [email protected]

Limora online

www.Limora.com

Neu

Содержание Mitsuba







Отзывы: