background image

 

Dear Customer

 

Thank  you  for  choosing  Lilliput’s  LCD  fish  finder.  This  product  adopts 

high-performance  embedded  computer  hardware.  It  is  designed  for  operations  under 

relatively  harsh  marine  environments  and  featuring  water  prove,  damp  prove, 

corruption  protection,  wide  voltage  range  protection  etc.  The  delicately  optimized 

design meets the requirements of all users in its applications to various conditions and 

occasions. Lilliput aims to server our customer with its excellent quality and exquisite 

manufacturing technology. 

We encourage you to read this installation and operations carefully in order to get full 

benefit from all the features and application of this product.   

Notice

 

 

Do not power on the equipment when the transducer is expose to the air. It might 
cause the damage to the transducer. 

 

Install the transducer according to the instruction. Do not bend, twist, pull or press 
the cable of the transducer. 

 

The  extension  cable  needs  to  put  inside  the  seal  terminal  box.  The  cable  of  the 
transducer is not allowed to touch the surface of the boat.   

 

Once the equipment’s power has been put into the “on” position do not switch the 
computer’s power

 

to the “off” position until the computer is fully booted. 

 

Please make sure that the power voltage setting has been adjusted to the standard 

voltage value of the location where the product is being used. 

 

Before using this product, please first make sure that all external wires and power 

adapters have been correctly connected. If you suspect any defects, please contact 

your sales agent or factory personnel immediately. 

 

Dust, humidity and dramatic temperature changes will affect the usage life of this 

computer. Please keep the machine away from these hazards.   

 

In  cleaning  the  units  do  not  use  chemical  detergents.  Remove  dust  with  a  soft 
cloth to ensure brightness. 

 
Warnings

 

High  Voltage  Circuit!  Disassembly  and  repair  of  device  should  only  be 
performed by authorized service personal. 
 
Power off the device from the plane immediately if there is water leaking into 
the  equipment.  Continuous  using  the  equipment  might  causes  short  circuit. 

Please contact our service under those circumstances.   

 

Do not attempt to modify or repair the original equipment. It may cause the 
damage of the precious electronic components inside the device. 

 

Power  off  the  device  from  the  plane  immediately  if  there  is  fire  or  smoke 
around.  Continuous  using  the  equipment  might  causes  short  circuit.  Please 

contact our service under those circumstances 

Содержание LCD Fish/Depth Finder
























Отзывы:

Похожие инструкции для LCD Fish/Depth Finder