background image

18

RE-CALIBRATION OF CRIMPING DIAMETER DIAL

NOTE: The crimping diameter dial has been calibrated at the factory during test run.

1. Re-calibrate the crimping diameter with ferrule 

(seamless steel tube), Ø 25 mm; wall 2 mm, by using 

the die set 32-19.

2. Set the dial at 1.0, so that the crimping diameter will be 

20 mm (see the adjacent picture) and lock the dial. 

Crimp the ferrule and measure the real diameter.

3. Remove the control dial knob  (avoid to turn the dial 

shaft at the same time).

4. Open the dial lock lever and set the real diameter into 

it (diameter of ferrule) relock it and install back.

5. Turn the dial to right diameter and crimp another 

ferrule. Now the machine has been calibrated and the 

real diameter should be the same than the diameter 

which state on the dial. If not, repeat from point 2 and 

be more careful when handling the dial.

6. After the adjustment, the crimping result should be the 

minimum nominal crimping diameter of each die set 

with the dial at 0.0.

GUARANTEE

The machines produced by Lillbacka Powerco Oy are guaranteed against defects in material and 

manufacture. Within the limits of the guarantee, the defective part will be replaced with a new one, or when 

possible, repaired free of charge.
The guarantee is valid for 12 months after commissioning, yet for a period not exceeding 18 months after 

delivery ex works Alahärmä, Finland.
The guarantee does not compensate for damage due to improper use, overload, neglect, or normal wear. 

Working and travelling costs as well as freight charges caused by guarantee repairs are not covered by the 

guarantee.
Guarantee repairs shall be carried out at Lillbacka Powerco Oy, Alahärmä, Finland, or by an authorized Finn-

Power service. In case guarantee repair is demanded, the customer has to prove that the machine is under 

guarantee.
LILLBACKA POWERCO OY DO NOT WARRANT FOR ANY INCIDENTAL OR CONSEQUENTIAL 

DAMAGAES, OR FOR ANY OTHER LOSS, DAMAGE OR EXPENSE OF ANY KIND, INCLUDING LOSS OF 

PROFITS.

19

TECHNICAL DATA

TECHNICAL DATA   P51

3-phase

Capacity

in

2½  (industrial hose 4”)

Crimping diameter range *)

Ø (mm)

10....87

Max opening

mm

46

Pump

l/min

17/5.7

Max pressure

bar

300

Crimping force

kN

2800

Theoretical production capacity

per hour 

720

Sound pressure level

dB(A)

71

Enclosure class

IP 54

Closing speed of master dies (max.) mm/s

7.9
Frequency 50 Hz

Motor power

kW

4

Voltage V / Current A / Fuse A

  230 / 15.3 / 25

  400 /  8.8 / 20

        /       /

Frequency 60 Hz

Motor power

kW

4.8

Voltage V / Current A / Fuse A

  230 / 15.2 / 25

  400 / 8.7 / 20

        /        /

*) with complete standard die equipment.

Special diameters and profiles to customer's specifications.

Overall dimensions:

Weight 260 kg, excluding oil.

READ THE INSTRUCTIONS THOROUGHLY TO SECURE SAFE AND CORRECT 

OPERATION OF THE MACHINE.

Содержание Finn-power P51MS

























Отзывы: