Lightware 91540021 страница 26 Скачать руководство пользователя

Страница: 26 / 119

4.DeviceConcept

HDMI-TPS-RX110AY series – User's Manual

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

4.6.4.

Relay Interface

HDMI-TPS-RX110AY receiver contains two relay modules which can be accessed by a 4-pole Phoenix

connector.TherelayscanbecontrolledbyLightwareprotocolcommands(LW3)andEventmanageractions

can be assigned to the port.

ATTENTION!

The device built with normally open (N.O.) contact relays which means when the unit is not

powered (DC plug is disconnected), the relays will open.

INFO:

The default state of each relay ports is open.

Application of Relays - Example

The Concept

Ceiling lamp is turned off by Relay 1 and projection screen is rolled down by Relay 2 when signal received

from the transmitter over TPS input line.

Settings of the Receiver

▪

Relay 1

:createaneventinEventmanager:whensignalispresentonInput1(I1)thensetRelay1to

be open. Also create another event when signal is not present on Input 1 (I1) then set Relay 1 to be
closed.

▪

Relay 2

:createaneventinEventmanagerwhensignalispresentonInput1(I1)thensetRelay2to

be closed. Also create another event when signal is not present on Input 1 (I1) then set Relay 2 to be
open.

WhenBlu-rayplayerstartstoplaythepresentationvideo,signalisreceivedoverTPSinputlinesoRelay1

opens which results turning off the lights, furthermore Relay 2 closes and the projection screen is rolled

down.Whenthepresentationisended,signalceasesontheTPSinputline,soRelay1closeswhichresults

turning on the lights, furthermore Relay 2 opens and projection screen returns to its enclosure.
See the details about the Event Manager settings in the

Event Manager

section.

4.6.5.

Consuming Electronic Control (CEC) Interface

DIFFERENCE:

This feature is available only in HDMI-TPS-RX110AY-Plus model.

ConsumerElectronicControl(CEC)isabi-directionalcommunication,definedintheHDMIstandard.This

featureisforremotecontrolofthesourceandsinkdevicesintheA/Vsystem.

HDMI-TPS-RX110AY-Plus model is able to send and receive CEC commands, from the input ports towards

the source, and from output port towards the sink. For more information about sending CEC messages, see

Sending CEC Commands

section.

CEC has a dedicated pin in the HDMI connector. DVI connector does not contain this pin, so the CEC

transmissionbrakeswhenHDMI-DVIconnectororadapterisinthesignalroute.

CEC Application Example

WhenactivesignalisdetectedonTPSin,thetransmittersendsaCECmessageautomaticallytotheHDTV

to wake up.

Createaneventintheeventmanager:

▪

Set as a condition, that the signal is present on the output (O1),

▪

Set as an action then send a CEC command 'Image view on' O1 output port.

See the details about the Event Manager settings in the

Event Manager

section.

ATTENTION!

The CEC command sending over TPS interface is working only with CEC-transparent

TPS transmitters. For the details please download our Using CEC in Lightware Devices document on

https://lightware.com/support/guides-and-white-papers

website.

4.6.6.

USB Control Interface

ThedevicecanbecontrolledoverfrontpanelUSBminiB-typeconnector.ThisinterfaceonlysupportsLW3

protocol.TheinterfacecanbeusedtoestablishaconnectiontoLightwareDeviceControllersoftware.

4.6.7.

Ethernet Control Interface

ThedevicecanbecontrolledoverfrontpanelEthernetstandardRJ45connectorwhichconnectedtoLAN.

ThisinterfacesupportsbothLW2andLW3protocols.
TheinterfacecanbeusedtoremotecontrolthedevicewithLightwareDeviceControllerandestablishthe

connectiontoLightwareDeviceUpdatersoftwareandperformfirmwareupgrade.



 



Содержание 91540021
























































































































Результаты поиска

Содержание 91540021

Отзывы:

Похожие инструкции для 91540021

Бренды по названию

Популярные бренды

Lightware 91540021, Руководство пользователя

Результаты поиска

Содержание 91540021

Отзывы:

Похожие инструкции для 91540021

Бренды по названию

Популярные бренды