background image

3

  

(13)

inDOMO HP

 - Platform lift

FINAL TESTS

IM.TEC.028.EN_rev.10.2

   -  November 2015

All rights reserved

MANUAL READING GUIDE

0.1 

CHAPTER SYMBOLS

General information

Positioning

2:1

2:1 lift specification

Box content

Installation

1:1

1:1 lift specification

Preliminary advice

Commissioning

Read carefully

Electrical Wiring

0.2 

IMPORTANT ITEMS

General safety warning

Important notice

Read carefully

Risk of electric shock

Risk of bodily injury (e.g. due to 

sharp angles or protruding parts)

Risk of damage to mechanical 

parts (e.g. during incorrect 

installation)

Fire hazard

Hanging load

Risk of skin injury

Risk of falling

No entry

Materials to be protected against 

bad weather conditions

0.3 

INDIVIDUAL SAFETY DEVICES

Hard hat

Ear protection

Safety harness and other 

accessories

Overalls

Safety steel-toe boots with ankle 

protection

Safety glasses

Dust masks

Work gloves

Rubber gloves

First aid kit

The words 

WARNING

 and 

CAUTION

 are used to highlight the following risks of injury and damage:

WARNING

Serious danger to safety

CAUTION

Risk of damage to materials which may lead to safety risks

Содержание InDomo HP














Отзывы: