Life Gear 75163 Скачать руководство пользователя страница 7

Страница: 7 / 25

HARDWARE PACKING LIST

Hex Head Bolt M6*47 ------------------------------------------------------------------------------------------2

Washer Ø 20 *Ø 8.5 * 1.5 ------------------------------------------------------------------------------------12

Lock Nut M8 --------------------------------------------------------------------------------------------------------6

Lock Nut M6 --------------------------------------------------------------------------------------------------------2

Washer Ø 16 *Ø 6.5 * 1.0 --------------------------------------------------------------------------------------4

Hex Head Bolt M8*23 ------------------------------------------------------------------------------------------2

Hex Head Bolt M8*50 ------------------------------------------------------------------------------------------2

Hex Head Bolt M8*38 ------------------------------------------------------------------------------------------2

Screw M6*20--------------------------------------------------------------------------------------------------------4

Screw M6*25--------------------------------------------------------------------------------------------------------4

Washer Ø 13 *Ø 6.5 * 1.0-------------------------------------------------------------------------------------- 8

Nut Cap Ø 27 *Ø 13.5--------------------------------------------------------------------------------------------2

Pivot Arm Reinforcement Plate----------------------------------------------------------------------------2

NOTE:

The parts described above are all the parts you need to assemble for this inversion table.

Before you start to assemble, please check the hardware packing to make sure they are
included.

All the other parts described in page 5 parts list are pre-assembled in the factory.

ASSEMBLY

Set all parts in a clear area on the floor and remove the packing materials. Refer to the part lists for help
to identify the parts. Follow the instructions to assemble this inversion table .

Part # Description Quantity

Double open wrench M12*14 (2PCS)

Содержание 75163


























Результаты поиска

Содержание 75163

Отзывы:

Похожие инструкции для 75163

Бренды по названию

Популярные бренды

Life Gear 75163, Руководство пользователя

Результаты поиска

Содержание 75163

Отзывы:

Похожие инструкции для 75163

Бренды по названию

Популярные бренды