Life Fitness Lifecycle 9500RHR Series Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 105

background image

Lifecycle 9500RHR Series Exercise Bikes

2

How To...REMOVE AND REPLACE THE ALTERNATOR

Tools Required:

3/4, 5/16, 1/2, and 1/4 inch wrenches.

STEP 1

Remove the HOUSING. Refer to “How To...” in this section.

STEP 2

Remove the two POSITIVE RED WIRES from
their POSTS on the ALTERNATOR. Using a 1/4
inch wrench, remove the two nuts securing the
BLACK FIELD WIRE and the YELLOW WIRE.
Then with a 5/16 inch wrench, remove the
REGULATOR TERMINAL NUT and the GROUND
TERMINAL NUT.

STEP 3

With a 1/2 inch wrench, loosen and remove the
ALTERNATOR ADJUSTMENT BOLT and two
WASHERS.

STEP 4

With two 3/4 inch wrenches, loosen the
ALTERNATOR PIVOT BOLT and LOCKNUT. DO
NOT remove the ALTERNATOR until STEP 7.

STEP 5

Push the ALTERNATOR forward to relieve the belt tension, then loop the BELT around the small FLYWHEEL
SHAFT. Once the BELT is free, temporarily set it on top of the PULLEY to keep it out of the way.

STEP 6

Remove the PIVOT BOLT and its three WASHERS from the ALTERNATOR.

STEP 7

Remove the ALTERNATOR and install the new ALTERNATOR in place.

STEP 8

Reverse this procedure for reassembly using specified torques, however note the following:

NOTE: THE ALTERNATOR BELT MUST BE PROPERLY POSITIONED ON THE LARGE PULLEY AND

ALTERNATOR FLYWHEEL. MISALIGNMENT WILL RUIN THE BELT AND PULLEY.

NOTE: USING A BELT TENSION GAUGE, MEASURE THE BELT TENSION. IF THE BELT TENSION

MEASURES LESS THAN 60-70 LBS., MAKE ADJUSTMENTS USING

THE ALTERNATOR ADJUSTMENT BOLT.

How To...REMOVE AND REPLACE THE

Alternator
Adjustment
Bolt

Washer

Alternator
Pivot Bolt

Belt

Locknut

Washer

Large Pulley

Detail

Belt

Alternator Fly Wheel

Alternator

Black / White
Field Return
Wire

Black
Ground Wire

Yellow Wire

Positive
Red Wires (2)

Orange

Torque Nuts
20-25 IN

LBS

Torque
30-35 ft-lbs

Torque
18-20 ft-lbs

«
...
41
42
43
44
45
...
»

Содержание Lifecycle 9500RHR Series










































































































Отзывы:

Нет отзывов

Похожие инструкции для Lifecycle 9500RHR Series

Бренд: BODYMAX Страницы: 32

Бренд: Reebok Страницы: 4

Бренд: Insportline Страницы: 22

Бренд: LifeSpan Страницы: 41

FOLDAWAY X-1000 PLUS

Бренд: Skandika Fitness Страницы: 60

Бренд: CARDIOSTRONG Страницы: 52

Бренд: Garneau Страницы: 14

Exercise Bike 95CXL

Бренд: Life Fitness Страницы: 1

Essential LCRT8-0XXX-01

Бренд: Life Fitness Страницы: 7

Бренд: AsVIVA Страницы: 62

Бренд: AsVIVA Страницы: 69

Бренд: Orbit Fitness Страницы: 13

Бренд: Body flex Страницы: 24

V-fit MOTIVE FITNESS

Бренд: U.N.O Страницы: 24

Бренд: Spirit Страницы: 64

Бренд: FitNord Страницы: 12

Бренд: Wattbike Страницы: 17

Бренд: BH FITNESS Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды