background image

11

CONTROLS AND INDICATORS

On/Alarm Silence/Manual Battery Test Button

This button controls output power to connected load(s) and has three functions:

On, Alarm Silence, and Manual Battery Test.  Pressing this button will start up 

the UPS in order to provide conditioned and protected power into the utility

socket.

To silence alarms, press this button for at least one half second while alarm

conditions are present.  After the alarm is silenced, the UPStation GXT™ will

reactivate the alarm system to alert of additional problems. 

Note:

 The low battery and bypass reminder alarms cannot be silenced.

To initiate a manual battery test, press this button for at least one half second 

while operating from utility power and no alarm conditions are present.

If the bottom two LEDs do not illuminate during a Battery Test, allow the UPS to 

recharge the batteries for 24 hours.  After 24 hours, retest the batteries.  If the 

batteries have been retested and the bottom two LEDs still do not illuminate,

contact your dealer or Liebert Technical Support (LTS) for a battery replacement 

kit.

Off/Bypass Button

This button controls output power to connected load(s) and has dual functions: 

Off and Bypass.

CAUTION:

  Pressing this button once will cause the load to be transferred to

bypass power.  Pressing this button a second time within 4 seconds will result in 

loss of power to the output sockets and connected loads.  Perform all necessary 

shutdown procedures on connected loads before pressing this button twice.

Load/Battery Level Indicators (4 Green, 1 Amber)

The Load/Battery Level indicators have dual functions.  During normal mode

operation LED indicators display the approximate electrical load placed upon the 

UPS; and during battery mode operation LED indicators display approximate

battery capacity.  Refer to the Typical Battery Discharge Curves to determine the 

approximate amount of back up time with respect to your connected load

percentage.

The UPStation GXT™ is equipped with automatic and remote battery test

features.  The automatic test occurs every 14 days if utility has not been

interrupted (14 day timer resets if unit goes to battery).  Should the battery fail 

this test, the fault indicator along with the A and C diagnostic LEDs will illuminate 

and an alarm will sound (refer to Troubleshooting Guide).  The remote test

feature functions with either SiteNet® 2 or SiteNet® SNMP Manager software

and can remotely initiate the battery test.

Fault Indicator (Red)

The Fault indicator is illuminated if the UPS has detected a problem. Also, one or 

more of the load/battery level indicators may be illuminated (refer to

Troubleshooting Guide).

Bypass Indicator (Amber)

The Bypass indicator is illuminated when the UPS is operating from bypass

power.  An alarm will sound indicating the UPS detected a problem, or the

manual bypass function has been activated.

DISCONTINUED 

PRODUCT

Содержание UPStation GXT1000MT-120





























Отзывы: