LG WF-S5707PP Скачать руководство пользователя страница 6

Страница: 6 / 56

2-2. CONNECTING W ATER SUPPLY HOSE

Before connecting Water Supply Hose to water tap, check your hose type

and choose correct instruction. Water Supply Hose may vary according to

the country.

Make sure connect blue inlet hose to cold water tab, and orange inlet hose

to hot water tab.

Connecting Water Supply Hose to water tap

Rubber packing

Water supply hose

Connector

Untighten the screw

Untighten the screw of the connector so
that the tap can be placed in the middle.

Fixing the connector to the tap

Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.

Attach the water supply hose to the connector

Push the water supply hose vertically
upwards so that the rubber seal within the
hose can adhere completely to the tap.

Check the connection of water supply hose and the connector

After connecting the hose, open the tap to
check for any water leakage.
In case of water leakage, close the tap and
start again from step 1

Fixing the connector of connector and water supply hose

Attach the water supply hose to the
connector and then tighten it by screwing it
to the right.

Normal Type

Normal tab without thread & screw type inlet hose.)

Содержание WF-S5707PP

























































Результаты поиска

Содержание WF-S5707PP

Отзывы:

Похожие инструкции для WF-S5707PP

Бренды по названию

Популярные бренды

LG WF-S5707PP, Руководство по обслуживанию

Результаты поиска

Содержание WF-S5707PP

Отзывы:

Похожие инструкции для WF-S5707PP

Бренды по названию

Популярные бренды