LG VX10000 Voyager Скачать руководство пользователя

Страница: 7 / 164

- 6 -

VX10000

LGE Internal Use Only

2.3 Voice Encoder and Variable Data Speed

The bi-directional voice service having variable data speed provides voice communication which employs voice

encoder algorithm having power variable data rate between the base station and the mobile station. On the other hand,

the transmit voice encoder performs voice sampling and then, creates encoded voice packets to be sent out to the

receive voice encoder, whereas the receive voice encoder demodulates the received voice packets into voice samples.

One of the two voice encoders described in the above is selected for use depending on inputted automatic conditions

and message/data; both of them utilize four-stage frames of 9600, 4800, 2400, and 1200 bits per second for Cellular

and 14400,7200,3600,1800 bits per second for PCS, so PCS provide relatively better voice quality (almost twice

better than the existing celluar system). In addition, this type of variable voice encoder utilizes adaptive threshold

values on selecting required data rate. It is adjusted in accordance with the size of background noise and the data rate

is increased to high rate only when the voice of caller is inputted.

Therefore, background noise is suppressed and high-quality voice transmission is possible under the environment

experiencing serious noise. In addition, in case the caller does not talk, data transmission rate is reduced so that the

transmission is carried out in low energy. This will reduce the interference on other CDMA signals and as a result,

improve system performance (capacity increased by about two times).

2.4 Protecting Call Confidentiality

Voice privercy is provided in the CDMA system by means of the private long code mask used for PN spreading.

Voice privacy can ve applied on the traffic channels only. All calls are initiated using the public long code mask for

PN spreading. The mobile station user may request voice privacy during call setup using the origination message or

page response message, and during traffic channel operation using the long code transition request order.

The Transition to private long code mask will not be performed if authentication is not performed. To initiate a

transition to the private or public long code mask, either the base station or the mobile station sends a long code

transition request order on the traffic channel.

2.5 Soft Handoff

A handoff in which the mobile station commences communications with a new base station without interrupting

communications with the old base station. Soft handoff can only be used between CDMA channels having identical

frequency assignments.

2.6 Frequency Re-Use and Sector Segmentation

Unlike the existing analog Cellular system, the CDMA system can reuse the same frequency at the adjacent cell.

there is no need to prepare a separate frequency plan. Total interference generated on mobile station signals received

from the cell site is the sum of interference generated from other mobile stations in the same cell site and interference

generated from the mobile station of adjacent cell site. That is, each mobile station signal generates interference in

relation to the signals of all the other mobile stations.

Z3X-BOX.COM

Содержание VX10000 Voyager




































































































































































Результаты поиска

Содержание VX10000 Voyager

Отзывы:

Похожие инструкции для VX10000 Voyager

Бренды по названию

Популярные бренды

LG VX10000 Voyager, Руководство по обслуживанию

Результаты поиска

Содержание VX10000 Voyager

Отзывы:

Похожие инструкции для VX10000 Voyager

Бренды по названию

Популярные бренды