LG UU09W ULD Скачать руководство пользователя страница 3

Страница: 3 / 49

Safety Precautions

Installation Manual

ENGLISH

To prevent the injury of the user or other people and property damage, the following instructions
must be followed.

Be sure to read before installing the air conditioner.

Be sure to observe the cautions specified here as they include important items related to safety.

Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.

The meanings of the symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Installation

Be sure not to do.

Be sure to follow the instruction.

Safety Precautions

Always perform
grounding.

• Otherwise, it may cause

electrical shock.

Don’t use a power
cord, a plug or a loose
socket which is dam-
aged.

• Otherwise, it may cause

a fire or electrical shock.

For installation of the
product, always con-
tact the service center
or a professional instal-
lation agency.

• Otherwise, it may cause

a fire, electrical shock,
explosion or injury.

Securely attach the
electrical part cover to
the indoor unit and the
service panel to the
outdoor unit.

• If the electrical part

cover of the indoor unit
and the service panel of
the outdoor unit are not
attached securely, it
could result in a fire or
electric shock due to
dust, water, etc.

Always install an air
leakage breaker and a
dedicated switching
board.

• No installation may

cause a fire and
electrical shock.

Do not keep or use
flammable gases or
combustibles near the
air conditioner.

• Otherwise, it may cause

a fire or the failure of
product.

1,MFL67855401,영영 2017. 6. 29. 영영 1:50 Page 3

Содержание UU09W ULD


















































Результаты поиска

Содержание UU09W ULD

Отзывы:

Похожие инструкции для UU09W ULD

Бренды по названию

Популярные бренды

LG UU09W ULD, Руководство по установке

Результаты поиска

Содержание UU09W ULD

Отзывы:

Похожие инструкции для UU09W ULD

Бренды по названию

Популярные бренды