manualshive.com logo in svg

LG THERMA V AHNW16606B0, Руководство по обслуживанию, Страница: 64 / 81

Поделиться
Скачать
LG THERMA V AHNW16606B0 Скачать руководство пользователя страница 64

- 64 -

53

Title

Communication

(PCB(Heater) 

’

PCB(Inverter))

• Communication poorly

• Power input AC 230V.
• The connector for transmission is disconnected.
• The connecting wires are misconnected.
• The communication line is shorted at GND.
• Transmission circuit of PCB(Inverter) is abnormal.
• Transmission circuit of PCB(Heater) is abnormal.

Display

code

Title

Cause of error

Check point & Normal condition

Check Point

1. Check the input power AC 230 V.
2. Check the communication wires are correctly connected.

Adjust the connection of wire Confirm the wire of "Live", "Neutral"

3. Check the resistance between communication line and GND. (Normal : Over 2MΩ)
4. Check the connector for communication is correctly connected.
5. Make sure you have connected to the communication line soldering

(If you do not connect by soldering, a communication error(CH05/CH53) occurs by noise)

WARNING

Before checking PCB(Inverter) or each outdoor electric parts, wait for 3 minutes after the power is off. When measuring at standby
state of power supply, after checking the measurement mode of the meter, be careful of the short-circuits with other parts.

Содержание THERMA V AHNW16606B0


















































































Отзывы:

Нет отзывов