LG THERMA V AHNW16606B0 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 81

LG THERMA V AHNW16606B0 Скачать руководство пользователя страница 4

- 4 -

1.3 Safety warnings and instructions

WARNING

Installation

• Ask the dealer or an authorized technician to install the air conditioner.

- Improper installation by the user may result in water leakage, electric shock, or fire.

• Take care to ensure that nobody could step on or fall onto the outdoor unit.

- This could result in personal injury and product damage.

• Always ground the product.

- There is risk of fire or electric shock.

• Always intstall a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric shock.

• For re-installation of the installed product, always contact a dealer or an Authorized

Service Center.
- There is risk of fire, electric shock, explosion, or injury.

• Do not install, remove, or re-install the unit by yourself (customer).

- There is risk of fire, electric shock, explosion, or injury.

• Do not store or use flammable gas or combustibles near the air conditioner.

- There is risk of fire or failure of product.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric shock.

•

Before beginning the service procedure, it is necessary to read the service manual.

•

The installation of the device has to be performed in accordance with the manual; otherwise the
manufacturer does not acknowledge the warranty.

•

Any remaking or replacement of original components of the device eliminates the manufacturer’s
guarantee for safe and functional operation. In the case of undesignated and incorrect use of the
device, the manufacturer is not responsible for the consequences and will not acknowledge claims for
damages in these cases. The user is solely responsible for injuries and damages on the device itself or
on other objects resulting from undesignated and incorrect use of the device.

•

Failure to comply with the manual and good practise while connecting the device to the power supply
can lead to serious injury or death.

•

Connecting the device to the power source can only be performed by a qualified installer.

NOTE

WARNING

1.2 General

«
...
2
3
4
5
6
...
»

Содержание THERMA V AHNW16606B0


















































































Отзывы:

Нет отзывов