LG THERMA V AHNW16606B0 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 65

LG THERMA V AHNW16606B0 Скачать руководство пользователя страница 64

64

Air-to-Water Heat Pump

Check Points, Maintenance and Troubleshooting

Airborne Noise Emission

The sound pressure of this product is below the 70 dB.
• The noise level can vary depending on the site.

The figures quoted are emission level and are not necessarily safe working levels. Whilst there is a correlation between
the emission and exposure levels, this cannot be used reliably to determine whether or not further precautions are
required. Factor that influence the actual level of exposure of the workforce include the characteristics of the work room
and the other sources of noise, i.e. the number of equipment and other adjacent processes and the length of time for
which an operator exposed to the noise. Also, the permissible exposure level can vary from country to country. This
information, however, will enable the user of the equipment to make a better evaluation of the hazard and risk.

Search the Manual Using Your Mobile

1. After running a QR Code reader app in your Smartphone, red the QR Code below.

2. Select the desired region.

3. Press the “

” on the top right and enter the model name.

4. Press “Support”.

5. Press “Manual & Documents”.

6. Select the manual that you want to see.

※

When installed, enter the model name and send it to the customer.

Sales Model Name (Indoor) :

Sales Model Name (Outdoor) :

«
...
62
63
64
65
»

Содержание THERMA V AHNW16606B0


































































Отзывы:

Нет отзывов